Sensors & Switches
A 3D printer has various microswitch sensors that are read by the printer's mainboard to determine the position of the print bed and the print head(s). There are also filament sensors to monitor whether the filament runs out halfway through the print and to pause the printer if necessary.
A temperature sensor in the hotend ensures that the 3D printer reaches the correct temperature to melt the filament and print properly.
-
End stop sensor for a.o. RepRap 3D Printer RAMPS
Optical end stop detection for every 3D printer or CNC machine.
I.a. for use with the RAMPS 1.4 board.
- Optical end stop switch
- 3 pin cable (length +/- 50cm) -
End stop sensor microswitch
Microswitch end stop detection for every 3D printer or CNC machine.
- Microswitch end stop.
- 3 pin cable (length +/- 70cm)
Board dimensions: 40mm x 16mm x 7m6mm In stock -
End stop sensor optical
Optical infrared end stop sensor, measures whether an object passes between the sensors. When there is an object between the sensors, the digital output is high, otherwise it is low.
Space between sensors: 5mm
Power supply: 3.3V-5V
Board dimensions: 3.2cm x 1.4cm
In stock -
End stop sensor optical
Optical end stop detection for any 3D printer or CNC machine.
- Optical end stop switch
- 3 pin cable (length +/- 100cm)
- Supply voltage: 2.7V ~ 5V
In stock -
Filament sensor for 3D printers
Filament sensor with cable, for 1.75mm filament.
The sensor detects when the filament has run out and reports this to the controller board of the 3D printer. In stock -
Microswitch push button (make contact) with lever
Dimensions: 12.7 x 5.8 x 6.6mm.
Single pole switch (SPDT). In stock -
Microswitch push button (make contact) with lever with roller
Dimensions: 19.9 x 6.3 x 14.4-23.8mm.
Single pole switch (SPDT).
Max. 3A / 250VAC In stock -
Microswitch push button (make contact) with lever with roller vertical
Single-pole switch (SPDT) with normally open (NO) and normally closed (NC) contact.
Max. 4A / 250VAC
Case Dimensions: 28mm x 16mm x 10mm
Contacts: 4.6 x 0.8mm In stock -
Temperature sensor thermistor 100K NTC for RepRap 3D printer 1m
Thermistor NTC temperature sensor for, among others, use with a 3D printer.
Impedance: 100KΩ
Accuracy: ±1%
Diameter: ∅1.1mm
Range: 200° / 300V
Length: ~15cm
Material: Teflon wire conductors
Thermistor head diameter: 1.8mm In stock -
Temperature sensor thermistor NTC 100K Ohm 3950 1% (loose)
Loose NTC 100K 3950 thermistor for 3D printers.
Resistance (R25 ℃): 100K Ω
Resistance (R25 ℃) allowable deviation: ± 1%
B-value: 3950k
Allowable error of B value: ± 1%
Temperature range: - 40 ℃ ~ 250 ℃
Dissipation coefficient: ≥ 2MW / ℃ (in still air)
As shown, so without connector. In stock -
Temperature sensor thermistor NTC 100K Ohm 3950 fast-replace
3950 NTC 100K Ohm thermistor for 3D printers.
With fast-replace JST SM 2 pin connector to quickly replace the thermistor without having to replace the entire cable.
The end of the cable has a 2-pin Dupont connector.
Sensor: 3950 NTC 100K &round;1.8mm
Cable length: 1m In stock -
Temperature sensor thermistor PT100 Fork plug for Ultimaker 2
High quality PT100 Thermistor temperature sensor for, among others. use with an Ultimaker 2 3D printer.
With extra shielding and extra wire for higher accuracy.
Connection: fork cable lug
Sensor dimensions: diameter: 3mm, length: 15mm
Cable length: 150cm
Temperature range: 0 ~ 450°C
-
Temperature sensor thermistor PT100 Molex for Ultimaker 2
High quality PT100 Thermistor temperature sensor for, among others. use with an Ultimaker 2 3D printer.
With extra shielding and extra wire for higher accuracy.
Connection: molex connector
Sensor dimensions: diameter: 3mm, length: 15mm
Cable length: 150cm
Temperature range: 0 ~ 450°C
-
Temperature sensor thermocouple K-type M3 stud screw-in
High quality K-type thermocouple temperature sensor for, among others. use with a 3D printer.
Connection: fork cable lug
Sensor dimensions: M3 thread
Cable length: 100cm
Temperature range: 0 ~ 300°C
In stock -
Temperature sensor thermocouple K-type M4 stud screw-in
High quality K-type thermocouple temperature sensor for, among others. use with a 3D printer.
Connection: fork cable lug
Sensor dimensions: M4 thread
Cable length: 100cm
Temperature range: 0 ~ 300°C
In stock -
Touch bed leveling sensor for 3D printers
3D Touch sensor for automatically leveling the print bed. With connection and mounting materials (some skill and familiarity with 3D printers is useful).
Working voltage: 5V
Current: 15mA (max. 300mA).
In stock
Shipping costs Netherlands
>
