Special Offers
Here you can find all the electronics offers from Bits & Parts. So, if you're looking for an electronics deal, check here!
Be quick, as some items are available only while stocks last!
-
Particle Xenon - nRF52840 with BLE + Mesh
Woohoo, it's time for a Particle Mesh party! And the Particle Xenon is the most basic element (ha!) for your mesh network. The Xenon is a low-cost mesh-enabled development board that can act as either a standalone endpoint or repeater for Particle Mesh networks . It is based on the Nordic nRF52840, the BLE Cortex M4 with a ton of Flash, RAM and ...
Adafruit Part number: 3999
In stock
-
Tie-wrap cable tie 300x5mm black bag 250 pieces
Bag with 250 pieces of black tie-wrap cable ties 300x5mm.
Length: ~300mm
Width: 5mm
In stock -
Fine Dust / Dust Sensor - Nova SDS011 PM2.5 High Precision - Serial Output
This SDS011 PM2.5 dust sensor from Nova measures airborne particles (fine dust) using a laser.
- Measures particles from 0.3 to 10µm
- With serial output (also to USB with the supplied CH340 USB-serial converter).
- Built-in fan.
- Works by scattering the laser light
Dimensions: 71mm x 70mm x 23mm In stock -
Prototyping platform acrylic for Arduino UNO
Set of an acrylic platform with screws, nuts and feet suitable for mounting an Arduino UNO and a 400 pin breadboard (not included).
In stock
-
Distance Sensor Ultrasonic Splashproof JSN-B02
An ultrasonic distance sensor similar to the HC-SR04 but splashproof and with the sensor on a separate wire so you can mount it elsewhere.
Sensor diameter: 25mm
Mounting hole: 22mm
Sensor height: 20.7mm
In stock -
Arduino Starter kit UNO R3
Large Arduino UNO starter kit with everything you need to get started with Arduino.
Contents:
- 1x Storage box
- 1x Arduino UNO (compatible) with USB cable
- 1x Breadboard 830 pins MB102 - universal experiment board white
- 1x Buzzer 5 Volt 12mm active
- 1x Mini speaker
- 1x Infrared remote control with 21 keys
- 1x Infrared receiver for remote co... In stock -
RFID RC522 Controller/Scanner Set 13.56MHz
With this set you can read and write Mifare RFID tags and cards. The module communicates via SPI and can be connected to the Arduino (see the connection diagram under documentation).
Cards and tags can be read contactlessly by holding them in front of the reader.
Delivered:
- the RFID sensor module
- straight and curved header pins
- a white credi... In stock -
Stepper motor 28BYJ-48 with ULN2003 driver board
A stepper motor can be made to rotate very precisely and stop at a specific point. This allows you to automatically open the sun blinds at a certain position, for example.
The supplied driver board makes connecting to an Arduino, for example, simple (see the connection diagram under documentation).
By alternately turning the coils in the motor on a... In stock -
Breadboard jumper cables in storage box 140PCS 22AWG
Various lengths of jumper cables with tinned ends for better contact.
140 pieces.
Wire gauge: 22AWG. In stock -
ESP8266 NodeMCU WiFi dev. board V3 - CH340 - ESP-12E
NodeMCU is an open-source firmware and development kit that helps you prototype an IoT (internet of things) product with just a few lines of Lua script.
Board dimensions: 49.3mm x 60mm x 4.8mm (13mm incl. pins)
USB chip: CH340G
For example, connecting to your network is done in a few lines:
wifi.setmode(wifi.STATION)
wifi.sta.config("SSID","pas... In stock -
Silicone Work Mat 34cm x 23cm x 4mm - Adafruit 3536
Color: Blue
This silicone mat is made of 4mm thick rubber and can take just about anything you throw at it. It's stable, strong, non-slip, non-conductive and heat-resistant surface for your workstation. We love it here at Adafruit because you can hot air boards right on top and there won't be any damage to our underlying worktable.
It's also skid... Adafruit Part number: 3536 -
Work mat magnetic 20x25cm
Handige magnetische werkmat voor het werken met kleine delen zoals schroefjes van bijvoorbeeld smartphones.
Door de vakindeling op de mat kun je de verschillende delen uit elkaar houden en met de meegeleverde stift markeren. Na gebruik kun je de inkt weer wissen met de wisser op de stift.
In stock -
Silicone work mat 34cm x 23cm x 5mm blue
This heat-insulating silicone work mat/soldering mat protects your desk or work table against heat from a heatgun or soldering iron (up to 500°C).
The handy compartments also make it easy to sort loose screws and parts and prevent them from getting lost.
With 20cm ruler.
Dimensions:
34cm x 23cm x 5mm
In stock -
Smart Car Chassis 4WD large with 4 motors
Smart car chassis kit 4WD. Nice set to craft a robot car yourself.
The set consists of:
1x car chassis (plexiglass)
4x DC motor with gear ratio of 1:48 (3 to 6 Volt)
4x wheel (66mm)
4x speed encoder
1x all necessary mounting materials
(battery box not included)
In stock -
Fine Dust / Dust Sensor - GP2Y1010AU0F - Analog Output
Sharp's GP2Y1010AU0F is an optical air quality sensor, designed to sense dust particles. An infrared emitting diode and a phototransistor are diagonally arranged into this device, to allow it to detect the reflected light of dust in air. It is especially effective in detecting very fine particles like cigarette smoke, and is commonly used in air pu...
In stock
-
Flash memory W25Q16BV SPI 16Mbit on breakout board
WinBond W25Q16BV flash memory with SPI interface on a breakout board.
Pinout:
VCC - 3.3V
GND - GND
CS - (chip select) CS/SS
CLK - (clock) CLK
DI - (data in) MISO
DO - (data out) MOSI
WP - (write protect)
HOLD - You'll probably never have to use this pin so I leave it wired to VCC (active low).
Explanation: https://www.instructables.com/id/How-to... In stock -
Temperature sensor 1-wire Waterproof - Dallas DS18B20 2 meters
1-Wire system temperature sensor easy to read digitally with, for example, an Arduino.
(Use the OneWire library to read the sensor.)
The nice thing about 1-wire is that you can connect several sensors in a row to the same wire.
This way you only use 1 wire on your Arduino for all your sensors!
Waterproof and made of stainless steel.
Dimensions: 6... In stock -
Charger for LiIon/LiPoly batteries Solar/USB/DC v2 - Adafruit 390
Make your projects green this summer with our specialized USB/Solar Lithium Ion Polymer Battery Charger! This charger has a very unique design, perfect for outdoor projects or DIY iPod chargers. We spent over a year testing and tinkering with this charger to create a plug and play solution for charging batteries with the sun and we are very pleased...
Adafruit Part number: 390
In stock
-
LED 10mm yellow clear
Yellow 10mm LED with clear lens.
In stock
-
LED 5mm RGB/multicolor clear color changing fast
5mm RGB LED that automatically changes color (about 7 colors).
This fast version first fades between the 7 colors (about 0.5s per color) and then flashes between the 7 colors (about 0.5s per color) and then starts over again.
Voltage: 3V DC. In stock -
Relay board 4-channel 5V - Solid state relay
Compared to traditional relays, Solid State Relay (SSR) has many advantages: it has a longer lifespan, a higher on/off switching speed and no noise. In addition, it is better protected against vibrations and mechanical shocks and is more suitable for humid environments.
This Solid State Relay Module has two channels, which can be controlled and op... In stock -
Breadboard 830 pins MB102 - universal experimenting board white
Breadboard 830 pins - universal experiment board.
Develop electronics projects without soldering!
This 830 pin breadboard will make your electronics hobby even more fun!
With self-adhesive back.
Easily interconnectable so you can continue to expand the breadboard.
Dimensions: 16.5cm x 5.5cm x 1cm
Color: white In stock -
Case Arduino UNO compact acrylic transparent
Simple case that protects the Arduino UNO from dust and accidental contact with other (metal) surfaces.
Easy to assemble yourself in 5 minutes.
Please note! Due to the thickness of the top plate, only shields with long pins will fit. In stock -
Raindrop meter analog/digital
This raindrop meter measures how much water is on its surface.
On the analog output (AO) you can measure how much water is on it with a signal between 0 and Vcc.
The digital output (D0) gives 0 or 1 depending on the threshold set with the potentiometer.
At a certain amount of water the output will go to 0. If it is dry or below the threshold the ou... In stock
Shipping costs Netherlands
>
