Programmers & Accessories
With a programmer, you can connect microcontrollers, such as those on an Arduino board or ESP microcontrollers, and upload a program. Generally, you connect a programmer to a USB port on a PC or Mac. There are also Arduino shields that allow you to program microcontrollers.
-
AVR ATMega8 Programming/Development board
An AVR ATMega8 Programming/Development board where you can easily insert and fix an ATMega IC (up to 28 pins) and then program it. For example, you can program the ATMega328 of an Arduino UNO.
The board has a standard 10 pin ISP download interface to which you can easily connect a USB programmer (see additional articles).
The board contains:
- Po... In stock -
AVRISP Shield for Arduino with buzzer
Did you know that you can burn Arduino bootloaders onto ATmega chips, making them Arduino compatible?
Previously you needed a breadboard and a lot of jumper wires for this, but with this AVR ISP shield it becomes a lot easier!
This shield is additionally equipped with a buzzer that indicates the progress of the bootloading/programming process.
Fi... In stock -
AVRISP USBasp USB programmer for Atmel AVR controllers
This programmer is based on the USBasp design by Thomas Fischl and connects to your computer via a USB port.
The USB interface is controlled by the ATmega processor, the rest is done by the firmware.
Bits & Parts always supplies a 10-pin cable!
Some features:
- Support for AVRDude from version 5.2 (http://www.nongnu.org/avrdude/)
- Reading a... In stock -
Adafruit AVR Sticker for breadboard Arduino-compatibles v.1 - Adafruit 554
1 AVR Sticker for an ATmega.
These stickers are a must for anyone making a breadboarded Arduino-compatible. They fit right on top of a DIP ATmega328 (or '168) chip, and clearly indicate every pin as it would be called in the Arduino IDE. No more looking up the datasheet or schematic! The stickers are made of a tough vinyl, usually used for bumper ... Adafruit Part number: 554 In stock -
Adafruit AVR Sticker for breadboard Arduino-compatibles v.2 - Adafruit 601
1 AVR Sticker for an ATmega.
These stickers are a must for anyone making a project with an ATmegaXX8 chip such as the ATmega48, ATmega8, ATmega88, ATmega168, or ATmega328. They fit right on top of a 28 pin DIP chip, and clearly indicate every pin by port name or common use for the I2C and SPI pins. No more looking up the datasheet or schematic! Th... Adafruit Part number: 601 In stock -
Adapter Atmel AVR 10 to 6 pins (ICSP ISP AVRISP USBASP STK500)
Adapter for connecting a USBASP programmer to the 6 ICSP pins of an Arduino.
For example, you can use this to quickly install a new bootloader on your Arduino.
You can also upload your program from the Arduino IDE to your Arduino. (Tools->Board->Arduino UNO (or whatever Arduino board you are programming), Tools->Programmer->USBasp, Tool... In stock -
Breakout adapter board for SWD cable (2x5 1.27mm) - Adafruit 2743
This adapter board is designed to make it easier to use ARM dev boards that use slimmer 2x5 (0.05"/1.27mm pitch) SWD cables for programming.
It's helpful for using products like the JTAGulator, STLink or SEGGER J-Link with tiny boards that use the 10-pin SWD programming connector, often Cortex M0 or M3's.
This board comes with no cables. It's r... Adafruit Part number: 2743 -
ST-Link STM8/STM32 v2 Programmer & Emulator - Adafruit 2548
Explore new microcontroller worlds with an ST-Link Programmer & Emulator / Debugging dongle. This little USB stick contains a microcontroller with the code for ST's classic programmer/emulator for STM8 and STM32 bit processors. Since STM's are so common, this tool will come in handy whenever you encounter them. You can even get 5V and regulated 3.3...
Adafruit Part number: 2548
In stock
-
USB Programmer for ESP8266
For connecting an ESP8266 to a computer via the USB port.
In stock
-
USB Programmer for ESP8266 with switch
For connecting an ESP8266 to a computer via the USB port.
With switch to make GPIO0 low to upload new firmware. (Or program with the Arduino IDE).
With 300mA 3.3V LDO voltage regulator.
With CH340G USB-to-serial chip. In stock
Shipping costs Netherlands
>
