• Voor 16u besteld, morgen in huis*
  • Kleine artikelen voordelig verzonden
  • Veilig betalen
  • Klanten geven ons een 9,0
  • Audioversterker 3,7W stereo Class D - MAX98306 - Adafruit 987

    Audioversterker 3,7W stereo Class D - MAX98306 - Adafruit 987
    Audioversterker 3,7W stereo Class D - MAX98306 - Adafruit 987
    Audioversterker 3,7W stereo Class D - MAX98306 - Adafruit 987
    Prijs:
    11,95 
    incl. BTW, excl. verzending
    Aantal:
    Artikelnummer:
    Adafruit 987
    Voorraad: In stock In voorraad
  • Snel en voordelig verzonden
  • Veilig betalen
  • Klanten geven Bits & Parts een 9,0/10 Link naar Kiyoh
  • Audioversterker 3,7W stereo Class D - MAX98306 - Adafruit 987

    Productinformatie:

    This incredibly small stereo amplifier is surprisingly powerful - able to deliver 2 x 3.7W channels into 3 ohm impedance speakers. Inside the miniature chip is a class D controller, able to run from 2.7V-5.5VDC. Since the amp is a class D, its incredibly efficient (over 90% efficient when driving an 8Ω speaker at over a Watt) - making it perfect for portable and battery-powered projects. It has built in thermal and over-current protection but we could barely tell it got hot. This board is a welcome upgrade to basic "LM386" amps!

    The inputs of the amplifier go through 1.0uF capacitors, so they are fully 'differential' - if you don't have differential outputs, simply tie the R- and L- to ground. The outputs are "Bridge Tied" - that means they connect directly to the outputs, no connection to ground. The output is a 360KHz square wave PWM that is then 'averaged out' by the speaker coil - the high frequencies are not heard. All the above means that you can't connect the output into another amplifier, it should drive the speakers directly.

    Comes with a fully assembled and tested breakout board with 1.0uF input capacitors. We also include header to plug it into a breadboard, 3.5mm screw-terminal blocks so you can easily attach/detach your speakers, and a 2x4 header + jumper to change the amplifier gain on the fly. You will be ready to rock in 15 minutes! Speakers are not included, use any 3ohm or greater impedance speakers.

    - Output Power: 3.7W at 3Ω, 10% THD, 1.7W at 8Ω, 10% THD, with 5V Supply
    - Passes EMI limit unfiltered with up to 12 inches (30 cm) of speaker cable
    - High 83dB PSRR at 217Hz
    - Spread-Spectrum Modulation and Active Emissions Limiting
    - Five pin-selectable gains: 6dB, 9dB, 12dB, 15dB and 18dB. Select with a jumper or by setting the G and G' breakout pins (see schematic for breakout board showing gain pin settings for details)
    - Excellent click-and-pop suppression
    Thermal and short-circuit/over-current protection
    - Low current draw: 2mA quiescent and 10uA in shutdown mode

    Klik om de website van dit product te openen.Klik om de website van dit product te openen.



    Over Bits & Parts

    iDEAL logo Betaalmethoden
    Rek.nr.: NL49RABO0106097385
    BIC: RABONL2U
    KvK.nr.: 58665196
    BTW.nr.: NL191426301B02

    Alle artikelen worden uit eigen voorraad vanuit Nederland verzonden.
    Meer info...

    Verzendkosten

    Artikelen passend door brievenbus (tot 350gr)*:
    Gratis verzonden bij bestelling vanaf 25€.
    Daaronder 1,95€ verzendkosten.

    Grotere artikelen:
    Gratis verzonden bij bestelling vanaf 80€.
    Daaronder 5,95€ verzendkosten.

    *Automatisch bepaald
    PostNL logo