Prototyping board PermaProto Pi Mini Kit - met EEPROM - Adafruit 2314

X
Prototyping board PermaProto Pi Mini Kit - met EEPROM - Adafruit 2314
Prototyping board PermaProto Pi Mini Kit - met EEPROM - Adafruit 2314
Prototyping board PermaProto Pi Mini Kit - met EEPROM - Adafruit 2314
Prototyping board PermaProto Pi Mini Kit - met EEPROM - Adafruit 2314
Prototyping board PermaProto Pi Mini Kit - met EEPROM - Adafruit 2314
Prototyping board PermaProto Pi Mini Kit - met EEPROM - Adafruit 2314
Prototyping board PermaProto Pi Mini Kit - met EEPROM - Adafruit 2314
Prototyping board PermaProto Pi Mini Kit - met EEPROM - Adafruit 2314
Prototyping board PermaProto Pi Mini Kit - met EEPROM - Adafruit 2314
Prototyping board PermaProto Pi Mini Kit - met EEPROM - Adafruit 2314
Prijs:
11,95 
incl. BTW, excl. verzending
Aantal:
Artikelnummer:
Adafruit 2314
In stock Direct uit voorraad leverbaar
Snel en voordelig verzonden
Verzendkosten voor kleine artikelen 2,95 €.
Boven 30,00 € gratis.
Veilig betalen
Klanten geven Bits & Parts een 9,3/10 Link naar Kiyoh
Logo brand

Prototyping board PermaProto Pi Mini Kit - met EEPROM - Adafruit 2314

Productinformatie:

Design your own Pi HAT, attach custom circuitry and otherwise dress your Pi A+, B+, or Pi 2 with this jaunty prototyping HAT kit with EEPROM

To kick off the Adafruit HAT party, we have this Perma-Proto inspired plug in daughter board. It has a grid of 0.1" prototyping soldering holes for attaching chips, resistors, LED, potentiometers and more. The holes are connected underneath with traces to mimic the solderless breadboards you're familiar. There's also long power strips for +3V, +5V and Ground connections to the Pi. Near the top we break out nearly every pin you could want to connect to the Pi (#26 didnt quite make the cut).

This is the fancier version of our Perma-Proto HAT. It comes with a printed circuit board and a single 2x20 GPIO Header for Raspberry Pi to put your Perma-Proto on top of your Raspberry Pi (like a nice little hat...) This version comes with a blank 24C32 I2C EEPROM soldered on and connected to the EEDAT/EECLK lines so you cannot 'stack' it with other HATs. However, you can program in the EEPROM to make a self-identifying setup using the Pi Foundations' HAT specs - please note the specifications are still under development.

You can customize your Perma-Proto setup using a standard 2x20 stacking header or extra tall 2x20 stacking header. You can also swap out the 2x20 header with a slim 2x20 type if you want it to sit closer to the Pi, or an extra tall one if you want it to sit above the USB/Ethernet ports.

A bit of light soldering is required to attach the header to the PCB but it's easy work.

This hat is only compatible with the Raspberry Pi A+, B+, or Pi 2! It will not work with the Raspberry Pi Model A or B.


Klik om de website van dit product te openen.Klik om de website van dit product te openen.

Aanvullende artikelen:

Draadset 9 kleuren 1x0,2mm² 24AWG vaste kern Draadset 9 kleuren 1x0,2mm² 24AWG vaste kern
15,95€
Direct uit voorraad
Headerpins male 40 pins metaal recht zwart Headerpins male 40 pins metaal recht zwart
0,25€
Direct uit voorraad
Schroefterminal blocks 2-voudig recht Schroefterminal blocks 2-voudig recht
0,45€
Direct uit voorraad
Schroefterminal blocks 3-voudig recht Schroefterminal blocks 3-voudig recht
0,65€
Direct uit voorraad