Infrared & Remotes
Everything related to infrared: infrared motion sensors, infrared transmitters and receivers, and distance sensors.
-
Distance sensor Infrared Sharp GP2Y0A41SK0F 4-30cm
The Sharp GP2Y0A41SK0F distance sensor/rangefinder measures distance in the range of 4-30cm with a reflected beam of infrared light. By using triangulation, the sensor can provide consistent values that are less affected by surface reflection. The Sharp GP2Y0A41SK0F provides an analog voltage that corresponds to the distance to the reflecting objec...
In stock
-
Distance sensor infrared/IR GP2Y0A02YK0F 20-150cm
The Sharp GP2Y0A02YK0F distance sensor/rangefinder measures distance in the range of 20-150cm with a reflected beam of infrared light. By using triangulation, the sensor can provide consistent values that are less affected by surface reflection. The Sharp GP2Y0A02YK0F provides an analog voltage that corresponds to the distance to the reflecting obj...
In stock
-
End stop sensor for a.o. RepRap 3D Printer RAMPS
Optical end stop detection for every 3D printer or CNC machine.
I.a. for use with the RAMPS 1.4 board.
- Optical end stop switch
- 3 pin cable (length +/- 50cm) -
End stop sensor optical
Optical infrared end stop sensor, measures whether an object passes between the sensors. When there is an object between the sensors, the digital output is high, otherwise it is low.
Space between sensors: 5mm
Power supply: 3.3V-5V
Board dimensions: 3.2cm x 1.4cm
In stock -
End stop sensor optical
Optical end stop detection for any 3D printer or CNC machine.
- Optical end stop switch
- 3 pin cable (length +/- 100cm)
- Supply voltage: 2.7V ~ 5V
In stock -
Infrared Break Beam/Interruption Sensor - 3mm - Adafruit 2167
The infrared break beam sensor allows you to check if an object passes between the two sensors.
On one side is an infrared sensor, on the other side an infrared receiver. If something passes between the sensor that does not let the invisible infrared light through, the receiver will let you know. Compared to PIR sensors, breakbeams are faster and ... Adafruit Part number: 2167 -
Infrared receiver BPV10NF 940nm 40°
Photo diode BPV10NF from Vishay for receiving infrared signals at high frequencies and high data rates.
The Vishay BPV10NF is ideal for designing transmission systems according to IrDA requirements and for frequency-based carrier systems (e.g. ASK/FSK coded, 450 kHz or 1.3 MHz).
Detection wavelengths: 790nm - 1050nm
Peak sensitivity at wavelength... In stock -
Infrared receiver LL-503PDD2E 940nm
Photo diode LL-503PDD2E from Lucky Light for receiving infrared signals.
Detection wavelengths: 700nm - 1200nm
Peak sensitivity at wavelength: 940nm
In stock -
Infrared receiver TOPS-030TB2 900nm
TOPS-030TB2 sensor for detecting infrared light with a wavelength of 900nm.
In stock
-
Infrared receiver TOPS-050TB2 900nm
TOPS-050TB2 sensor for detecting infrared light with a wavelength of 900nm.
In stock
-
Infrared receiver Vishay TSOP4833; 33kHz; 45°
In stock
-
Infrared receiver Vishay TSOP4838; 38kHz; 45°
-
Infrared reflection sensor TCRT5000L (Line follower sensor)
This module with the TCRT5000L infrared sensor can be used to make a robot follow a line.
The module has a digital and an analog output. The analog output gives the amount of reflected infrared light (which it also transmits). The digital output gives a high or low signal depending on the amount of reflection. The sensitivity is adjustable with adj... In stock -
Infrared reflection sensor optocoupler CNY70
CNY70 Sensor for detecting lines or obstacles, for example.
Brand: Vishay
In stock -
Infrared reflection sensor optocoupler TCRT5000
Small reflection sensor of the TCRT5000 type, for example to make a line follower yourself.
The TCRT5000 sensor has an infrared LED and an infrared receiver transistor next to each other. The emitted infrared light is reflected and received by the transistor. By looking at the difference in reflection you can detect a line or the line on the rotati... In stock -
Infrared remote control
Now control your project with this 21-button infrared remote control!
Check out the infrared library for the Arduino at the link below.
Please note! This is only the transmitter, you still need an infrared receiver to receive the infrared signals. (See additional articles.)
(Delivered without battery.)
In stock -
Infrared remote control set 38kHz
Remote control set consisting of an infrared remote control with numbers 0-9, *, #, OK, and up/down/left/right buttons, an infrared receiver and an infrared LED to make your own transmitter.
In stock -
Infrared transmitter/receiver set 38KHz HX1838
Set of an infrared receiver and transmitter.
Frequency: 38KHz
Voltage: 5VDC In stock -
LED 5mm Infrared Super-bright 940nm - Adafruit 388
Infrared LEDs are used for remote controls (they're the little LEDs in the part you point at your TV) and "night vision" cameras, and these little blue guys are high powered!
They have a wavelength of 940nm, which is what almost all devices listen to. They have a beam width of 20 degrees and work great for any kind of remote control application.
T... Adafruit Part number: 388 In stock -
LED 5mm Infrared/IR CQY99 Vishay TSUS5402 950nm
-
LED 5mm Infrared/IR Vishay TSAL7400 940nm
In stock
-
Motion sensor/detector Infrared PIR - AM312
Compact mini motion sensor based on an AM312 pyroelectric PIR sensor.
Operating voltage: 2.7-12VDC
Static power consumption: In stock -
Motion sensor/detector Infrared PIR - HC-SR501
With this HC-SR501 sensor your Arduino can detect movement in a room!
When motion is detected you will get an adjustable time 3.3V high signal on the output. (Adjustable with VR1).
Then the HC-SR501's output goes low for 3 seconds to prevent double triggering.
Adjustable resistor VR1 determines how long the output goes high when motion is detecte... In stock -
Motion sensor/detector Infrared PIR - SR602
Compact mini motion sensor based on an SR602 pyroelectric PIR sensor.
Operating voltage: 3.3-15VDC
Static power consumption: 20µA
Output: high (3.3V) - low (0V)
Delay time: ~2.5 seconds (changeable by changing a resistor).
Block time: 2 seconds
Lens dimensions: 10x10mm
An F3 photodiode can be connected to the S- and S+ connections.
In stock -
Motion sensor/detector Infrared PIR - with relay
Mini built-in infrared motion sensor with relay from Velleman.
Features:
- with automatic day/night identification
- adjustable sensitivity and activation time
- for built-in
Specifications:
- switch type: relay
- observation angle: 100°
- detection range: 8 m (@ 22 °C)
- max. load: 800 VA (max. starting current 3.5 A)
- power supply: 180-240... -
Motion sensor/detector Infrared PIR mini - SR505
This small SR505 motion sensor provides a high output signal for +/-25 sec. after detecting motion.
Dimensions: 23x10mm
Supply voltage: 4.5-20VDC
Consumption: In stock
Shipping costs Netherlands
>
