New at Bits & Parts
-
Rubber foot for housings 20x16x10.5mm
Foot to screw onto the bottom of a housing. With hole for the screw, screw not included.
There is a metal ring in the base for extra sturdiness.
Diameter: 20-16mm
Height: 10.5 mm In stock -
Motor kit - 4x motor/gear/cable
Set of 4 small motors (Motor DC 3-6V Type 130), 4 small gears (14T) and 8 connecting cables.
In stock -
USB Chassis part USB-A Female AF90-type3
In stock
-
USB Chassis part USB-A Female AF90-type2
In stock
-
USB Chassis part USB-A Female AF90-type1
In stock
-
Schroef / Parker kruiskop RVS M2 x 8,0mm met platte kop
In stock
-
Fan Radial 40x40x10mm 5VDC
Radial fan 40x40x10 on 5 volt DC for 3D printers.
Dimensions: 40mm × 40mm × 10mm
Rated Voltage: 5VDC
In stock -
Fan Axial 6020 60x60x20mm 24VDC
Axial fan 6020 for 3D printers on 24V DC.
Dimensions: 60mm x 60mm x 20mm.
Distance between the holes: 50mm
Voltage: 24VDC
Cable length: ±25cm
Connector: XH2.54-2P In stock -
Audio amplifier 2x120W stereo 12-26V Class D (TPA3116)
The XH-M543 stereo amplifier module with the powerful TPA3116 amplifier chip is a compact Class-D audio amplifier for makers and audio projects.
With up to 2x120W output power (at 24V), this module is ideal for DIY speakers, smart audio setups, and projects with Arduino, Raspberry Pi, ESP32, and ESP8266.
Thanks to the efficient design, high signal-... -
Button Droplet Mixer Style Black/Red
Knob for use on potentiometers with a 6mm shaft, among others. Suitable for electronics projects and mixing consoles.
Diameter: 10.2mm-15mm
Height: 17mm
In stock -
Capacitor SMD 100uF 50V electrolytic
In stock
-
Battery holder 18650 battery x 1
Battery holder with connecting cables (150mm) that accommodates a type 18650 battery.
Equipped with a hole in the bottom allowing the holder to be screwed onto a printed circuit board.
Length: 75mm
Width: 20mm
Height: 19mm -
Gas sensor MQ-139 (Freon)
The MQ-139 gas sensor breakout is a compact sensor module for detecting volatile organic compounds (VOCs) and solvent gases (Freon). Suitable for applications such as air quality measurements, gas detection, and experimental measurement setups.
Thanks to the breakout board, the sensor can be easily connected to a microcontroller such as an Arduino... In stock -
Rod/Shaft 2mm/2.5mm metal set of 76 pieces
Set van 76 metalen asjes voor het gebruik in kleine mechanische installaties.
Ook geschikt voor het maken of repareren van kleine speelgoed- of modelbouw-loopwerkjes.
Diameter: 2mm
Lengtes:
- 4 stuks 15mm
- 4 stuks 18mm
- 4 stuks 30mm
- 4 stuks 40mm
- 4 stuks 50mm
- 4 stuks 66mm
- 4 stuks 75mm
- 4 stuks 95mm
- 4 stuks 100mm
- 4 stuks 150mm
Diamet... In stock -
Rod/Shaft 2mm metal set of 40 pieces
Set of 40 metal shafts for use in small mechanical installations.
Also suitable for making or repairing small toy or model-building movements.
Diameter: 2mm
Lengths:
- 4 pieces 15mm
- 4 pieces 18mm
- 4 pieces 30mm
- 4 pieces 40mm
- 4 pieces 50mm
- 4 pieces 66mm
- 4 pieces 75mm
- 4 pieces 95mm
- 4 pieces 100mm
- 4 pieces 150mm
In stock -
Display Raspberry Pi 3.5 inch TFT touchscreen 320×480px (ILI9486)
This 3.5-inch TFT display is specifically designed for the Raspberry Pi and serves as a compact replacement for an external monitor. With a resolution of 320 × 480 pixels and a bright LED backlight, the screen offers a clear display for a wide range of applications.
The display uses the ILI9486 driver and communicates via the SPI interface, allow... In stock -
Fire sensor/ Flame sensor YG1006 on Grove board
The Grove-Flame Sensor can be used to detect fire sources or other light sources of the wavelength in the range of 760nm - 1100 nm.
It is based on the YG1006 sensor which is a high-speed and high-sensitive NPN silicon phototransistor. Due to its black epoxy, the sensor is sensitive to infrared radiation. As a result, the module is mainly used to d... In stock -
Real Time Clock/RTC DS1307 I2C - Grove
The Grove RTC module is based on the clock chip DS1307, which supports the I2C protocol. It utilizes a Lithium cell battery (CR1225).
The clock/calendar provides seconds, minutes, hours, day, date, month, and year. The end of the month date is automatically adjusted for months with fewer than 31 days, including corrections for leap years.
The clo... In stock -
Arduino KDuino with built-in TB6612FNG motor driver
The Arduino UNO with motor driver KRduino Black Edition is a powerful and compact microcontroller that combines the reliability of the classic Arduino UNO with a built-in motor driver. Perfect for robotics and motor-driven projects, it makes controlling motors and sensors simple and efficient.
This board is your ultimate tool for motor-driven proj... In stock -
Motor DC 3-6V for smart cars and robots with single metal shaft
With a reduction gearbox for a gear ratio of 1:48.
This motor has a single metal shaft.
Operates on 3 to 6 volts direct current.
At 3 volts:
In stock -
Magnetic tool holder / toolbar 66cm
Tidying up your tools becomes much easier with this magnetic wall tool holder. Simply 'stick' them to the magnetic strip. With the included mounting brackets and screws, you can easily mount them to any wall. The holders can be interconnected.
Available in various lengths.
Length: 66cm / 24inch In stock -
Magnetic tool holder / toolbar 50cm
Tidying up your tools becomes much easier with this magnetic wall tool holder. Simply 'stick' them to the magnetic strip. With the included mounting brackets and screws, you can easily mount them to any wall. The holders can be interconnected.
Available in various lengths.
Length: 50cm / 18inch In stock -
Magnetic tool holder / toolbar 30cm
Tidying up your tools becomes much easier with this magnetic wall tool holder. Simply 'stick' them to the magnetic strip. With the included mounting brackets and screws, you can easily mount them to any wall. The holders can be interconnected.
Available in various lengths.
Length: 30cm / 12inch In stock -
IC 74HC165 (SN74HC165N) - 8-bit Parallel-to-Serial Shift Register
The SN74HC165N is a handy IC that allows you to read multiple digital signals using fewer pins on your microcontroller. Instead of using 8 separate inputs, you can use this chip to read 8 signals via a single data line.
For example, you connect buttons, switches, or sensors to the 8 inputs (A through H). With a few control pins (clock and load), y... In stock -
Euro plug flat 230V / 10A white - PAWBOL
Among other things, for replacing the plug of, for example, a table lamp or for supplying power to a circuit.
In stock -
Solar LiPo Charger bq25185 3.3V buck board - Adafruit 6092
This compact module from Adafruit combines a LiPo battery charger and a 3.3V voltage regulator in one board. You can easily charge a battery via USB, DC, or a solar panel, and power your project at the same time.
Thanks to the built-in buck converter, the module delivers a stable 3.3V output up to 1A, ideal for microcontrollers such as Arduino, ES... Adafruit Part number: 6092 In stock -
Schroef / Parker kruiskop RVS M2 x 8,0mm met bolle kop
In stock
-
Silicone wire set multi-core 24AWG 0.2mm² 5 colors x 10m
5 colors of silicone wire in a handy storage box. The wire has a diameter of 0.2mm² (24AWG) and a length of 10 meters per roll.
Silicone wire is very flexible and highly resistant to heat and cold.
Colors: red / black / yellow / blue / green.
Length: 5x 10m In stock -
NFC Coin Tag 25mm 13.56MHz NTAG215
These round NFC tags (⌀25 mm, 1 mm thick) are equipped with the NTAG215 chip and are suitable for various applications such as Amiibo, automation, and data sharing. The tags are water-resistant, durable, and rewritable.
They work with NFC-enabled smartphones and apps like TagMo, and are ideal for smart homes, Wi-Fi sharing, business cards, 3D pr... In stock -
Audio decoder Stereo DAC I2S - PCM5102
With this PCM5102A DAC module, you convert digital audio into high-quality analog sound output. Ideal for significantly improving the sound of your Raspberry Pi or ESP32 compared to standard audio solutions.
The module operates via the I2S interface and has a built-in 3.5 mm audio output, allowing you to connect an amplifier or speakers directly.
... In stock -
Grub screw Stainless Steel
Stainless steel grub screw.
Choice of the following sizes:
M2.5x3 / M2.5x4 / M2.5x5 / M3x3 / M3x4 / M3x5 / M3x6 / M4x4 / M4x5 / M4x6
-
Glass fuses assortment of 160 pieces - 5x20mm slow-blow/fast-blow
Never fumble for the wrong glass fuse again with this 160-piece fuse set and a handy storage box.
Type: 5x20mm (F)
Contents:
Fast:
10x800mA (F0.8A)
10x1.25A (F1.25A)
10x1.6A (F1.6A)
10x2A (F2A)
10x2.5A (F2.5A)
10x3.15A (F3.15A)
10x4A (F4.0A)
10x6.3A (F6.3A)
Slow:
10x800mA (T0.8A)
10x1.25A (T1.25A)
10x1.6A (T1.6A)
10x2A (T2A)
10x2.5A (T2.5A)
10x... In stock -
Housing Universal ABS 56x58x28mm
Universal ABS housing for electronics projects.
With a separate lid that clicks on.
Dimensions: 56mm x 58mm x 28mm In stock -
Universal ABS Housing (splash)waterproof IP65 320x240x110mm
A really substantial large case in grey ABS with a transparent lid for housing your electronics project in a humid environment.
IP65: Splash-proof, not for underwater use!
Dimensions: 320mm x 240mm x 110mm
Color: gray In stock -
Universal ABS Housing (splash)waterproof IP65 230x150x85mm
A nice large case in grey ABS with a transparent lid for housing your electronics project in a humid environment. With mounting tabs to screw the case onto something.
IP65: Splash-proof, not for underwater use!
Dimensions: 230mm x 180mm x 85mm
Color: gray In stock -
Housing Universal ABS (splash)waterproof IP65 158x90x60mm
Gray ABS housing with transparent lid for housing your project in a humid environment.
IP65: Splash-proof, not for underwater use!
Dimensions: 158mm x 90mm x 60mm
Color: gray In stock -
Housing Universal ABS (splash)waterproof IP65 65x58x35mm
Gray ABS housing with a transparent lid for housing your project in a humid environment. With mounting tabs to screw the housing onto something.
IP65: Splash-proof, not for underwater use!
Dimensions: 65mm x 58mm x 35mm
Color: gray In stock -
Fan/Ventilator radiaal 80x73x25mm 12VDC
Radiale fan 80 x 73 x 25mm voor 3D printers (oa. Ultimaker) op 12V gelijkspanning.
Afmetingen: 80mm x 73mm x 25mm.
Afstand tussen de gaten: 80mm
Voltage: 12VDC
Stroom: ~0,18A
Connector: XH2.54-2P In stock -
Fan axial 4007 40x40x7mm 24VDC
Axial fan 4007 for 3D printers on 24V DC.
Dimensions: 40mm x 40mm x 7mm.
Voltage: 24VDC
Connector: XH2.54-2P
In stock -
Fan Axial 4007 40x40x7mm 12VDC
Axial fan 4007 for 3D printers on 12V DC.
Dimensions: 40mm x 40mm x 7mm.
Voltage: 12VDC
Connector: XH2.54-2P
In stock -
Fan Axial 3007 30x30x7mm 5VDC - 2 Parallel
2 Axial fans 3007 in parallel for, among others, Raspberry Pi on 5V DC.
With mounting bolts and nuts.
Dimensions: 30mm x 30mm x 7mm.
Distance between the holes: 24mm
Voltage: 5VDC
Connector: Dupont In stock -
Fan Axial 3007 30x30x7mm 5VDC
Axial fan 3007 for, among others, Raspberry Pi on 5V DC.
With mounting bolts and nuts.
Dimensions: 30mm x 30mm x 7mm.
Distance between the holes: 24mm
Voltage: 5VDC
Connector: Dupont -
Fan axial 4020S 40x40x20mm 5VDC
Axial fan 4020S for cooling in 3D printers and other electronics projects. This fan operates on 5V DC.
Dimensions: 40mm x 40mm x 20mm.
Distance between the holes: 32mm
Voltage: 5VDC
Cable length: ±15cm
Connector: XH2.54-2P In stock -
Radial fan 40x40x20mm 5VDC
Radial fan 40x40x20 for cooling in 3D printers and other electronics projects. This fan operates on 5V DC.
Dimensions: 40mm × 40mm × 20mm
Cable length: ±28cm
Connector: XH2.54-2P
Rated Voltage: 5VDC
(Images of 12V version) In stock -
Axial Fan 2510 25x25x10mm 5VDC
Axial fan 2510 for cooling in 3D printers and other electronics projects. This fan operates on 5V DC.
Dimensions: 25mm x 25mm x 10mm.
Voltage: 5VDC
Connector: XH2.54-2P In stock -
Axial Fan 4010S 40x40x10mm 5VDC
Axial fan 4010S for cooling in 3D printers and other electronics projects. This fan operates on 5V DC.
Dimensions: 40mm x 40mm x 10mm.
Distance between the holes: 32mm
Voltage: 5VDC
Connector: XH2.54-2P In stock -
Axial Fan 8010 80x80x10mm 12VDC
Axial fan 8010 for cooling in 3D printers and other electronics projects. This fan operates on 12V DC.
Dimensions: 80mm x 80mm x 10mm.
Voltage: 12VDC
Connector: XH2.54-2P In stock -
Axial Fan 2510 25x25x10mm 12VDC
Axial fan 2510 for cooling in 3D printers and other electronics projects. This fan operates on 12V DC.
Dimensions: 25mm x 25mm x 10mm.
Voltage: 12VDC
Connector: XH2.54-2P In stock -
Axial Fan 8025 80x80x25mm 12VDC
Axial fan 8025 for cooling in 3D printers and other electronics projects. This fan operates on 12V DC.
Dimensions: 80mm x 80mm x 25mm.
Voltage: 12VDC
Connector: XH2.54-2P In stock -
Fan axial 6015 60x60x15mm 12VDC
Axial fan 6015 for cooling in 3D printers and other electronics projects. This fan operates on 12V DC.
Dimensions: 60mm x 60mm x 15mm.
Distance between the holes: 50mm
Voltage: 12VDC
In stock -
Speaker set 8 Ohm 5 Watt Stereo in enclosure
Set of two 8 Ohm/ 5W speakers (2) in enclosure.
With a cable of ~80cm.
Suitable for making a voice assistant or your own Bluetooth speaker, among other things.
Impedance: 8 Ohm
Power: 5W
Dimensions: 100mm x 45mm x 21mm
Distance between mounting holes: 92mm / 36mm.
In stock -
Smart Car Chassis 4WD Mecanum Aluminum Double
Smart car chassis kit 4WD with a double aluminum frame and 4 Mecanum wheels. With Mecanum wheels, you can move not only forwards and backwards but also left and right (by rotating the motors in opposite directions). A fun set for building your own robot car.
Dimensions: (LxWxH) 250mm x 142mm x 73mm
The set consists of:
1x double car chassis (alu... In stock -
Smart Car Chassis 4WD Mecanum Aluminum Single
Smart car chassis kit 4WD with a single aluminum frame and 4 Mecanum wheels. With Mecanum wheels, you can move not only forwards and backwards but also left and right (by rotating the motors in opposite directions). A fun set for building your own robot car.
Dimensions: (LxW) 250mm x 142mm
The set consists of:
1x single car chassis (aluminum)
4x... In stock -
Digital multimeter UNI-T UT133A
UNI-T digital multimeter (type UT133A) for measuring DC and AC voltage, DC and AC current, resistance, capacitance and continuity.
Additionally, you can measure temperature (with the included K-type thermocouple) and test diodes.
- Over-voltage/over-current audible alarm
- High voltage warning
- Auto power off (can be turned off)
- Low consumption... In stock -
Digital multimeter UNI-T UT131B
UNI-T digital multimeter (type UT131B) for measuring direct and alternating voltage, direct current, resistance and continuity.
You can also test diodes and batteries.
- Auto power off
- Low consumption
- With buzzer for continuity (circuit) measurements
- Test diodes
- Tests 1.5V, 9V and 12V batteries (indicates good/low/bad)
- With space for the... In stock -
Digital multimeter UNI-T UT131A
UNI-T digital multimeter (type UT131B) for measuring DC and AC voltage, DC current, resistance, capacitance and continuity.
You can also test diodes.
- Auto power off
- Low consumption
- With buzzer for continuity (circuit) measurements
- Test diodes
- With space for the measuring pins
- Works on 2 AAA penlite batteries (included)
- With auto off ... In stock -
Crocodile clip set 28-piece in storage box
With this 28-piece crocodile clip set in a handy storage box, you will never be short of the right crocodile clip again.
Contents:
10x crocodile clips uninsulated 50 mm
6x crocodile clips insulated 55 mm
2x crocodile clips insulated 60 mm
6x crocodile clips insulated 65 mm
2x crocodile clips insulated 80 mm
2x crocodile clips 70 mm insulated In stock -
Speaker 4 Ohm 30 Watt 100mm - Dynavox
A slightly larger speaker with 30 watts of power and 4 ohms of impedance. Perfect for when your electronics project or voice assistant needs a bit more volume. Or simply if you want to build your own speakers.
Specifications:
Diameter: 100mm
Impedance: 4 Ohms
Resonance frequency: 97 Hz
Frequency response: 60Hz - 4kHz
Sound pressure: 91 dB (+/-3d... In stock -
Speaker 8 Ohm 30 Watt 100mm - Woofer - Dynavox
A slightly larger speaker with 30 watts of power and an 8-ohm impedance. Perfect for when your electronics project or voice assistant needs a bit more volume. Or simply if you want to build your own speakers.
For the low tones!
Specifications:
Diameter: 100mm
Impedance: 8 Ohms
Resonance frequency: 100Hz
Frequency range: 30-220Hz
Sound pressure: 8... In stock -
Display E-Paper 2.13 inch 212x104px MH-ET Live black/red with controller
The MH-ET Live 2.13-inch E-Paper display (black/red/white) is an energy-efficient display with a resolution of 296 × 128 pixels, ideal for projects that require an easy-to-read display with minimal power consumption.
Thanks to e-ink technology, the image remains visible without continuous power. The display only consumes power during refresh and ... In stock -
Display E-Paper 2.13 inch 212x104px MH-ET Live black with controller
The MH-ET Live 2.13-inch E-Paper display (black/white) is an energy-efficient screen with a resolution of 296 × 128 pixels, ideal for projects that require an easy-to-read display with minimal power consumption.
Thanks to e-ink technology, the image remains visible without continuous power. The display only consumes power during refresh and consu... In stock -
Display E-Paper 1,54inch 200x200px MH-ET Live black/red with controller
The MH-ET Live 1.54 inch E-Paper display (black/white) is an energy-efficient display with a resolution of 200 × 200px pixels, ideal for projects that require an easy-to-read display with minimal power consumption.
Thanks to e-ink technology, the image remains visible without continuous power. The display only consumes power during refresh and co... In stock -
Gouging knife set 12-piece
Gouging knife set with 12 different blades for gouging or working on wood, linoleum and other soft materials.
-
Heat shrink tubing assortment 560 pieces red/black in storage box
Set of 560 pieces of heat shrink tubing in various sizes, in red and black.
Contents:
20x Ø13mm
24x Ø10mm
24x Ø7mm
26x Ø6mm
26x Ø5mm
40x Ø4mm -
ESP32-C6 Seeed Studio Xiao Development Board WiFi/Bluetooth with Antenna
Seeed Studio XIAO ESP32C6 is powered by the highly-integrated ESP32-C6 SoC, built on two 32-bit RISC-V processors, with a high-performance (HP) processor with running up to 160 MHz, and a low-power (LP) 32-bit RISC-V processor, which can be clocked up to 20 MHz.
There are 512KB SRAM and 4 MB Flash on the chip, allowing for more programming space, ... In stock -
Power plug Jack Plug Male DC 2.5x5.5mm Long (14mm)
Male power plug with an inner diameter of 2.5mm and an outer diameter of 5.5.
To solder a wire yourself.
Dimensions: 2.5 x 5.5mm.
Plug length: 14mm In stock -
Power plug Jack Plug Male DC 2.5x5.5mm
Male power plug with an inner diameter of 2.5mm and an outer diameter of 5.5.
To solder a wire yourself.
Dimensions: 2.5 x 5.5mm.
Plug length: 9mm In stock -
UV Solder Mask Set for PCBs
UV solder mask kit for repairing printed circuit boards. Use the syringe and brush to apply the UV-sensitive varnish to the PCB where traces or damage need to be masked. Then, expose the varnish to the UV lamp for 5 to 10 seconds until it hardens.
The UV lamp works on 3 AAA penlite batteries (not included).
In stock -
Water valve with 3/4 inch screw connection 12VDC
Normally, the valve is closed, preventing water from passing through. When energized, the valve opens.
With G3/4 connection (Gardena).
Voltage: 12VDC
Current: ~500mA
Working pressure: 0.02 ~ 0.8MPa
Maximum water pressure: 2MPa In stock -
Desoldering ribbon set with 5 widths (1.5mm/2mm/2.5mm/3mm/3.5mm x 1.5m)
Desoldering tape. This allows you to "suck up" liquid solder so you can desolder components from a printed circuit board.
This is a set of 5 widths so you always have the right solder tape at hand.
Widths: 1.5mm / 2mm / 2.5mm / 3mm / 3.5mm
Length per roll: 1.5 meters
In stock -
Solder Lead-free Sn99.3Sn/Cu0.7 Ø1.0mm tube 15g - Velleman
Looking for reliable solder of excellent quality? Then this lead-free solder tin with resin core is just what you need!
It consists of 99.3 % tin (Sn), 0.7 % copper (Cu), has a diameter of 1 mm and comes in a tube.
The melting point is 230°.
- Lead-free: Lead-free solder is environmentally friendly and poses no risk to human health.
- Easy to u... In stock -
Universal battery tester
Universal battery tester with digital display for testing 1.5V and 9V household batteries.
Batteries you can test with this tester:
1.5V: AAA, HP6, MN2400, RO3, AA, HP7, MN1500, UM3C, HP11, MN1400, UM2, D, HP2, MN1300, UM1 and button cells.
9V: PP3, MN1604, 6F22, 006P
In stock -
Solder Lead-free Sn99.3/Cu0.7 Ø0.6mm roll 100g Velleman
Looking for reliable solder of excellent quality? Then this lead-free solder tin with resin core is just what you need!
It consists of 99.3% tin (Sn), 0.7% copper (Cu), has a diameter of 0.6 mm and is wound on a 100g roll.
The melting point is 230°.
- Lead-free: Lead-free solder is environmentally friendly and poses no risk to human health.
- E... In stock -
Desoldering pump Velleman
With a desoldering pump you can quickly and easily suck liquid tin away from your circuit, allowing you to remove components and wiring. A handy tool that always comes in handy when soldering circuits.
In stock
-
Desoldering pump big Velleman
Extra large and powerful desoldering pump from Velleman. This tin extractor is a bit larger, so it can suck up more tin at once.
A desoldering pump allows you to quickly and easily remove liquefied tin from your circuit, allowing you to remove components and wiring. It's a handy tool that always comes in handy when soldering circuits.
Diameter: 2... In stock -
Signal connector Aviation GX16 8 pin male/female
This GX16D circular connector set consists of a male and female connector (8 pins) and is ideal for creating reliable, detachable connections in electronic applications. Thanks to its robust metal housing and practical push-pull locking system, this connector provides a firm and secure connection.
The connector is made of zinc alloy with a nickel ... In stock -
Signal connector Aviation GX16 10 pin male/female
This GX16D circular connector set consists of a male and female connector (10 pins) and is ideal for creating reliable, detachable connections in electronic applications. Thanks to its robust metal housing and practical push-pull locking system, this connector provides a firm and secure connection.
The connector is made of zinc alloy with a nickel... In stock -
Signal connector Aviation GX16 6 pin male/female
This GX16D circular connector set consists of a male and female connector (6 pins) and is ideal for creating reliable, detachable connections in electronic applications. Thanks to its robust metal housing and practical push-pull locking system, this connector provides a firm and secure connection.
The connector is made of zinc alloy with a nickel ... In stock -
Signal connector Aviation GX16 3 pin male/female
This GX16D circular connector set consists of a male and female connector (3 pins) and is ideal for creating reliable, detachable connections in electronic applications. Thanks to its robust metal housing and practical push-pull locking system, this connector provides a firm and secure connection.
The connector is made of zinc alloy with a nickel ... In stock -
Plastic propeller with 4 blades yellow 56mm
Plastic propeller with 4 blades for mounting on a 2mm shaft.
Great for craft projects, experiments, and demos.
Diameter: ~56mm
Axle: 1.95mm In stock -
Buck converter Step Down DC-DC Uin:14-26V Uout:12V/3A MP1584EN
Compact step-down converter for reducing a DC voltage of 14V to 26V to an output voltage of 12V.
Handy for use on a breadboard or for building into a compact circuit.
Input voltage: 14-26V DC
Output voltage: 12V DC
Maximum current: 0.8A (peak 3A)
Conversion efficiency: 96%
Output ripple: In stock -
Buck converter Step Down DC-DC Uin:7-26V Uout:5V/3A MP1584EN
Compact step-down converter for reducing a DC voltage of 14V to 26V to an output voltage of 12V.
Handy for use on a breadboard or for building into a compact circuit.
Input voltage: 7-26V DC
Output voltage: 5V DC
Maximum current: 1.6A (peak 3A)
Conversion efficiency: 96%
Output ripple: In stock -
Buck converter Step Down DC-DC Uin:5.3-26V Uout:3.3V/3A MP1584EN
Compact step-down converter for reducing a DC voltage of 14V to 26V to an output voltage of 12V.
Handy for use on a breadboard or for building into a compact circuit.
Input voltage: 5.3-26V DC
Output voltage: 3.3V DC
Maximum current: 1.8A (peak 3A)
Conversion efficiency: 96%
Output ripple: In stock -
Buck converter Step Down DC-DC Uin:11-26V Uout:9V/3A MP1584EN
Compact step-down converter for reducing a DC voltage of 11V to 26V to an output voltage of 9V.
Handy for use on a breadboard or for building into a compact circuit.
Input voltage: 11-26V DC
Output voltage: 9V DC
Maximum current: 1.1A (peak 3A)
Conversion efficiency: 96%
Output ripple: In stock -
ATX PC Power Supply Tester with LCD Display
This powerful power supply tester is designed for quickly and easily testing PC power supplies. Suitable for ATX, BTX, and ITX power supplies, it's ideal for both hobbyists and professionals who want to quickly verify a power supply's proper functioning.
Thanks to the clear LCD display, all voltages are clearly displayed. The tester automatically ... In stock -
Accelerometer/Gyroscope/Compass - BNO055 (9DOF)
The MCU-055 BNO055 is an advanced 9-axis motion sensor with built-in sensor fusion. In a single compact module, this sensor combines a 3-axis accelerometer, 3-axis gyroscope, and 3-axis magnetometer (compass), supplemented by a 32-bit Cortex M0+ microcontroller that processes all measurement data internally.
Thanks to the built-in Bosch sensor fus... -
LED Ring 8x WS2812 RGB 5050 RGB LEDs with drivers (8bits)
Ring with 8 WS2812 5050 RGB LEDs.
The LEDs can be controlled individually (on/off, color and brightness) with only 2 wires from e.g. an Arduino.
See:
https://github.com/FastLED/FastLED
https://www.tweaking4all.nl/hardware/arduino/arduino-ws2812-led/ In stock -
Scissors with laser
Ever have trouble cutting straight?
Not anymore with these laser scissors ! The built-in laser shines directly on the surface you're cutting, ensuring a straight cut.
Battery included.
-
Holder for soldering wires
Handy holder to hold 2 wires for soldering.
Dimensions: 5 x 7 cm. -
Transistor set 300-piece PNP/NPN
Handy set of common transistors for the advanced electronics hobbyist.
Quantity: 300 pieces
Contents:
S9012 - 20 pieces
S9013 - 20 pieces
S9014 - 20 pieces
S8050 - 20 pieces
S8550 - 20 pieces
2N3904 - 20 pieces
2N3906 - 20 pieces
BC327 - 20 pieces
BC337 - 20 pieces
TL431 - 20 pieces
MPA42 - 20 pieces
MPA92 - 20 pieces
A1015 - 20 pieces
C1815 - 2... In stock -
Terminal adapter for Nano 3.0 presoldered
You can plug your Arduino Nano into this terminal adapter and have all inputs and outputs available on the screw terminals.
This allows you to easily connect all your sensors, servos, motors and other input/outputs to the Nano.
Supplied fully pre-soldered so you can get started with this adapter right away. In stock -
Transistor set 840-piece PNP/NPN
Handy set of common transistors for the advanced electronics hobbyist.
Quantity: 840 pieces
Contents:
BC327 PNP - 35 pieces
BC337 NPN - 35 pieces
BC517 NPN - 35 pieces
BC547 NPN - 35 pieces
BC548 NPN - 35 pieces
BC549 NPN - 35 pieces
BC550 NPN - 35 pieces
BC556 PNP - 35 pieces
BC557 PNP - 35 pieces
BC558 PNP - 35 pieces
2N2222 NPN - 35 pieces
2N... In stock -
Disassembly tool prying tool single-sided 124mm
This prying tool is a multifunctional opening tool for safely opening electronic devices. It's ideal for loosening housings, shields, and connectors without damaging sensitive components.
The tool is suitable for repairing and disassembling smartphones, tablets, laptops, and other electronic devices. Its slim and sturdy design allows for precise w... In stock -
PCB cleaning brush anti-static ESD safe - 2-fold
Anti-static 2-fold brush for cleaning printed circuit boards and sensitive equipment.
Length: 15cm
In stock -
Disassembly tool prying tool double-sided Jakemy
The JAKEMY prying tool is a multifunctional opening tool for safely opening electronic devices. This tool is ideal for loosening housings, screens, and connectors without damaging sensitive components.
The tool is suitable for repairing and disassembling smartphones, tablets, laptops, and other electronic devices. Its slim and sturdy design allows... In stock -
Wireless charger/receiver set 5V / 2A
This wireless charging set consists of a transmitter (charger) and receiver which can be used to wirelessly charge electronics close by (1-20mm).
Easy to use in a circuit due to its small size.
Specifications:
- Input Voltage: 5~12VDC
- Output Voltage: 5VDC
- Output Current(maximum): 2000mA
- Transmitter Coil Inductance: 30uH
- Transmit-receive d... In stock -
Laptop Cleaning Kit
A compact set for cleaning laptops, monitors and other electronic devices — a highly effective solution for maintaining delicate electronics.
The Laptop Cleaning Kit includes a non-flammable, alcohol-free LCD/TFT cleaning fluid (neutral pH6.0 ±2.0), a soft microfiber cloth (30×30cm), and a precise polypropylene cleaning swab.
The liquid effi... In stock -
Paper shredder oil 250ml
Discover a new standard of maintenance for your shredder with tihs shredder oil – your key to long-lasting and trouble-free operation in any office, home, or institution.
Carefully formulated to meet the demands of professionals, this shredder oil is more than just a maintenance product. It’s a solution that enhances your shredder, ensuring i... In stock -
Spare tip/soldering tip for Bakon BK90 - Ø0.5mm
Replacement tip BK600-B for Bakon BK80 soldering stations.
This point has a diameter of 0.5mm. In stock -
Raspberry Pi M.2 HAT+ SC1166
The SC1166 is a Raspberry Pi M.2 HAT+ board that enables you to connect M.2 peripherals such as NVMe drives and AI accelerators to Raspberry Pi 5’s PCIe 2.0 interface, supporting fast (up to 500MB/s) data transfer to and from NVMe drives and other PCIe accessories.
Raspberry Pi 5’s single-lane PCI Express 2.0 interface is exposed on a 16-pin,... In stock -
Arduino Nano R4 ABX00142 without pre-installed header pins
The Arduino® Nano R4 is a Nano form factor board based on the RA4M1 series microcontroller from Renesas (R7FA4M1AB3CFM#HA0), which embeds a 48 MHz Arm® Cortex®-M4 microprocessor. The Nano R4's memory is larger than its predecessors, with 256 kB flash, 32 kB SRAM and 8 kB data memory (EEPROM).
The Nano R4 board operates at 5 V, making it hardwar... In stock -
Arduino Nano R4 ABX00143 with pre-installed header pins
The Arduino® Nano R4 is a Nano-sized printed circuit board based on the Renesas RA4M1 series microcontroller.
(R7FA4M1AB3CFM#HA0), which incorporates a 48 MHz Arm® Cortex®-M4 microprocessor.
The Nano R4's memory is larger than its predecessors, with 256 KB of flash memory, 32 KB of SRAM, and 8 KB of data memory (EEPROM).
The Nano R4 board operat... In stock -
Epoxy Potting Compound 149
A two-component condensation material designed for hermetically sealing and insulating electronic, electrical, telecommunication and radio engineering components.
This Epoxy Potting Compound 149 stands out among similar products — its greatest advantages include high mechanical strength, exceptional adhesion to various materials and excellent e... In stock -
Thermal paste Carbon syringe 1g
Advanced thermal paste with carbon nanoparticles sets a new standard in electronics cooling. With an impressive thermal conductivity of 15.2 W/mK, it effectively and rapidly dissipates heat from processors, GPUs, and other high-temperature components. Its innovative formula has been created for demanding users – from gamers and overclockers to IT...
In stock
-
Soldering flux RF800 bottle with brush 100ml
Welcome to the world of hassle-free soldering with Flux RF800, the ideal solution primarily for your SMD (Surface Mount Device) soldering projects. Whether you are an experienced professional or an electronics enthusiast, Flux RF800 offers a revolutionary solution. It is the perfect soldering product, ensuring excellent connections and the highest ...
In stock
-
Label remover - Label Killer 300ml
Label remover, designed with professionals and cleaning enthusiasts in mind. Label Killer allows for easy and effective removal of labels, glue, and tough stains from various surfaces. Ideal for cleaning office equipment, household appliances, and devices in customer service points. Thanks to its gentle formula, it is safe for most surfaces, ensuri...
In stock
-
Thread insert set M3 480-piece
Set of 240 threaded inserts and 240 M3 bolts in various lengths.
Contents:
Threaded inserts (M3 x length x outer diameter):
- 50 pieces M3 x 3.0 x 4.2
- 50 pieces M3 x 4.0 x 4.2
- 50 pieces M3 x 5.0 x 4.2
- 50 pieces M3 x 6.0 x 4.2
- 40 pieces M3 x 8.0 x 4.2
Bolts (M3 x length):
- 50 pieces M3 x 5
- 50 pieces M3 x 6
- 50 pieces M3 x 8
- 50 piece... In stock -
USB Chassis part Dual USB-A / USB-C female
USB chassis part with a female USB-A and a female USB Type C connection for installation.
Suitable for power supply only, not for data transfer.
Maximum current: 2A
Cable length (22AWG): ~7cm
-
USB Chassis part Dual USB-A female
USB chassis part with 2 female USB-A connections for installation.
Suitable for power supply only, not for data transfer.
Maximum current: 2A
Cable length (22AWG): ~7cm
In stock -
LED 5mm Yellow Flat Top
Yellow LED with a diameter of 5mm and a flat top.
These LEDs can be mounted flush with a surface, creating a sleek design.
Voltage: 2.3V
Current: 20mA
Brightness: 500~1500 mcd
Grid spacing: 2.54mm
In stock -
LED 5mm Blue Flat Top
Blue LED with a diameter of 5mm and a flat top.
These LEDs can be mounted flush with a surface, creating a sleek design.
Voltage: 2.3V
Current: 20mA
Brightness: 500~1500 mcd
Grid spacing: 2.54mm
In stock -
LED 5mm Green Flat Top
Green LED with a diameter of 5mm and a flat top.
These LEDs can be mounted flush with a surface, creating a sleek design.
Voltage: 2.3V
Current: 20mA
Brightness: 500~1500 mcd
Grid spacing: 2.54mm
In stock -
Membrane keypad 1x3 red/yellow/green for Arduino
Keypad with red, yellow and green buttons.
With self-adhesive back.
Dimensions: 20x57x1mm
Button diameter: 11.5mm
Cable length: approx. 90mm. In stock -
Raspberry Pi 4B Aluminum Case Black with 2 fans
Sturdy aluminum housing with built-in heatsinks and fans for the Raspberry Pi 4B.
The heatsinks are attached to the case for optimal cooling. Included heatsink pads ensure good heat dissipation.
Easy to assemble yourself with the supplied screws and screwdriver.
Color: Black In stock -
Super glue bottle 20 grams
This super glue in a handy bottle provides strong adhesion on many surfaces within seconds.
Suitable for bonding wood / metal / porcelain / ceramic / glass / plastic and much more.
Not suitable for polyethylene / polypropylene / thin absorbent surfaces and items that are constantly wet.
When in doubt, always test in a hidden area.
Caution! Wear... In stock -
Super glue bottle with brush 10 grams
This super glue in a handy bottle with a brush provides strong adhesion to many surfaces within seconds.
Suitable for bonding wood / metal / porcelain / ceramic / glass / plastic and much more.
Not suitable for polyethylene / polypropylene / thin absorbent surfaces and items that are constantly wet.
When in doubt, always test in a hidden area.
... In stock -
Bluetooth receiver/amplifier DIY kit
This Bluetooth audio receiver and amplifier kit is a fun and practical DIY project for anyone who enjoys building electronics. The kit includes an MH-M18 Bluetooth module, an HT6872 audio amplifier chip, and all the necessary components to solder and assemble a complete mini audio system.
Once assembled, the system works via both Bluetooth and a 3... In stock -
ESP32 Voice chat assistant DIY kit
DIY kit for making a voice chat assistant for example for Home Assistant.
This kit contains all the parts you need to make the circuit yourself.
The kit contains:
- ESP32 S3 16R8 development board
- INMP441 MEMS I2S Microphone module
- MAX98357A Audio amplifier 3W Class D I2S
- 0.91 inch OLED screen
- 2 pieces 400 hole breadboards
- 3W speaker wit... In stock -
Window/Door Sensor Magnetic Reed Switch Wired Flush-Mounted NC RC33
Magnetic window/door sensor for mounting on the windowsill or doorframe. It detects whether a window or door is opened or closed.
For making your own alarm system / anti-burglary system.
As soon as the loose magnet part comes close to the other part, the switch switches off and the connection between the wires is broken (normally closed).
Detecti... -
Window/Door Sensor Magnetic Reed Switch Wired Flush Mount NO RC33A
Magnetic window/door sensor for mounting on the windowsill or doorframe. It detects whether a window or door is opened or closed.
For making your own alarm system / anti-burglary system.
As soon as the loose magnet part comes close to the other part, the switch turns on and the wires are connected to each other (normally open).
Detection distance... In stock -
Smoke extractor with arm
With this fume extractor with a handy arm, you can finally enjoy an odor-free and fume-free environment while soldering. The fume extractor is specially designed to effectively remove pungent odors and harmful fumes, allowing you to work in a healthy and comfortable environment.
The fume extractor is equipped with a quiet fan that ensures a peacef... In stock -
Hot air gun McPower 1500W max. 500°C
A powerful heat gun that's indispensable for working with heat shrink tubing, removing or drying paint layers, shaping plastic, and many other jobs. Compact, reliable, and suitable for both hobby and professional use.
Specifications:
Two heat settings:
- 300 l/min at 350 °C
- 500 l/min at 550 °C
Power: 1500W
Supply voltage: 230 V / 50 Hz
Inc... In stock -
Battery Button Cell CR2025 3V Lithium
CR2025 Button cell with a voltage of 3V.
Diameter: 20mm
Height: 2.5mm
Voltage: 3.0 Volt
In stock -
Battery Button Cell CR1632 3V Lithium
CR1632 Button cell with a voltage of 3V.
Diameter: 16mm
Height: 3.2mm
Voltage: 3.0 Volt
In stock -
Circle cutter 30-120mm
With this handy tool you can easily cut circles with a diameter of approx. 30-120 mm, cutting depth of approx. 30 mm.
For example, thin wood, plastic, thin aluminum or plasterboard.
Easy to adjust, clamp onto a cordless screwdriver or drill.
Includes: 1 x 8mm centre drill bit and 1 x mounting pin (if no hole needs to be drilled in the round reces... -
Gas sensor bare board
Loose board for installing an MQ gas sensor yourself. With adjustable sensitivity for the digital output.
With LED indicator for power and digital output level.
Operates on 5V DC. In stock -
Charger for 18650 Li-Ion batteries 3A XTAR-SC2
This charger can charge 2 batteries/accumulators of the types listed below.
The charger connects to a USB port or USB power supply using the included cable. Charging with a QC3.0 USB power supply allows charging at up to 3A.
LEDs indicate the status of the batteries.
Suitable for battery types:
18650 / 18700 / 20700 / 21700 / 22650 / 25500 / 26650... In stock -
Insulating tape PVC 10mx15mm brown
Handy tape for quickly insulating wires.
Color: brown
Width: ~15mm
Length: ~10 meters In stock -
LED Power Supply 12V / 200W Electronic - McShine
200W Power Supply for 12 Volt LEDs.
A rectifier converts the AC voltage into a constant 12V DC voltage, and a series capacitor protects the LEDs from overvoltage spikes. Furthermore, the device is protected against short circuits and overheating.
Easy to connect with screw terminals.
With 2 plus and 2 minus connections.
Dimensions: 310mm x 53mm ... In stock -
Voeding/Adapter 5-12V QC 3.0 19,5W gelijkspanning schakelend USB A - XLayer
USB QC 3.0 power supply for quickly charging phones or powering other USB devices.
- Universally applicable for all USB devices
- Protection against excessive current flow, overloading and overheating
- USB Power Delivery 3.0, QC 3.0 certified
Specifications:
- Input voltage: 230 V AC
- Output: 3,6 - 6,5V / 3A, 6,5 - 9V / 2A, 9-12V / 1,5A (max. 1... In stock -
Mechanical gripper - Spring-back
Handy spring-loaded gripper for easily grabbing and holding small components and parts.
Length: 11.5cm In stock -
Barometric pressure sensor/altimeter/temperature/gas sensor - BME680
BME680 4-in-1 Environmental Sensor – Temperature, Humidity, Air Pressure & Air Quality (VOC)
The BME680 is an advanced 4-in-1 MEMS sensor that measures temperature, humidity, air pressure, and VOCs (volatile organic compounds). It offers a complete solution for monitoring air quality and environmental conditions in a single, compact device.
Tha... In stock -
LED Ring set 40x WS2812 5050 RGB LEDs with drivers
With this 4-piece set you can make a ring with 40 WS2812 RGB LEDs.
The segments can be interconnected (soldered), so that all 40 LEDs can be controlled individually with 1 signal pin from an Arduino/Raspberry Pi or other MCU.
For example, you can make a clock this way.
Download the Adafruit Neopixel library or FastLED library for programming examp... In stock -
Wire 1x2.0mm² multi-stranded flexible core 5 meters black
A 5-meter roll of black-sheathed copper wire with a 2mm multi-stranded flexible core for use in electronics and other craft projects.
External: 3.2mm In stock -
Battery holder for button cells CR2032/LIR2032 single
Holder for 1 CR2032/LIR2032 button cell battery with on/off switch and cable.
In stock
-
Motor kit - fan/holder/battery box
Set for experimenting with a DC motor.
Contains a motor (3VDC), a blue fan, a motor holder and a 2xAAA battery box.
In stock -
LED Level indicator - 8 LEDs common cathode blue
LED Level indicator board with 8 blue individually controllable LEDs.
Useful for making outputs visible or creating a level indicator.
Simply connect all the LED pins to your Arduino, Raspberry Pi, ESP or other microcontroller and turn them on and off.
This is the common cathode version, meaning all the negative terminals of the LEDs are connecte... In stock -
LED Level indicator - 8 LEDs common anode blue
LED Level indicator board with 8 blue individually controllable LEDs.
Useful for making outputs visible or creating a level indicator.
Simply connect all the LED pins to your Arduino, Raspberry Pi, ESP or other microcontroller and turn them on and off.
This is the common anode version, meaning all the positive terminals of the LEDs are connected ... In stock -
LED Level indicator - 8 LEDs common cathode red
LED Level indicator board with 8 red individually controllable LEDs.
Useful for making outputs visible or creating a level indicator.
Simply connect all the LED pins to your Arduino, Raspberry Pi, ESP or other microcontroller and turn them on and off.
This is the common cathode version, meaning all the negative terminals of the LEDs are connected... -
LED Level indicator - 8 LEDs common anode red
LED Level Indicator Board with 8 individually controllable red LEDs. Useful for visualizing outputs or creating a level indicator.
Simply connect all the LED pins to your Arduino, Raspberry Pi, ESP or other microcontroller and turn them on and off.
This is the common anode version, meaning all the positive terminals of the LEDs are connected toge... In stock -
USB Tester - KWS-V30 black
USB Tester with IPS Color Display – 6-in-1 Power Meter (4–30V, 0–6.5A)
Compact and intelligent USB tester with a bright IPS color display for accurately measuring voltage, current, power, capacity, and charge time. Ideal for testing chargers, power banks, USB devices, and fast-charging technologies.
Key Features:
- Measure: Voltage (4–30V... -
Desoldering needle set - 8-piece stainless steel - 0.8 to 2.0 mm
This desoldering needle set is ideal for safely and efficiently removing components from printed circuit boards. The hollow needles are made of stainless steel and designed to slide easily over the pins of electronic components, allowing you to desolder them with a soldering iron without damaging printed circuit boards.
Application:
Place the corr... In stock -
Motor kit - fan/battery box
Simple DC motor with propeller and battery holder for your own craft experiments.
In stock -
Motor & Gear DIY Kit - Mechanical Building Kit 109 Pieces
This comprehensive, 109 pieces, mechanical building kit contains everything you need to build simple robots, vehicles, and experimental mechanical structures. Perfect for STEM education, hobby projects, or Arduino experiments.
The set includes a wide variety of gears, axles, motors, wheels, propellers, timing belts and mounting hardware, allowing ... In stock -
Vibration sensor - Tap/Shock piezo sensor
This piezoelectric vibration and shock sensor is ideal for detecting touch, tap, and vibration in Arduino and other microcontroller projects. The sensor utilizes the piezoelectric effect: vibration or tapping generates an electrical charge, which the module converts into a usable signal. Thanks to its high sensitivity, the sensor can be adjusted fr...
In stock
-
Switch rocker snap-in on/off light ASW-17D red
Rocker switch for switching 12V lighting such as a fog light.
Depending on how the switch is connected, the LED will either stay on or turn on/off (see explanation in the images).
Switches up to 12VDC/35A. In stock -
Rocker Snap-In On/Off Light Switch ASW-17D Green
Rocker switch for switching 12V lighting such as a fog light.
Depending on how the switch is connected, the LED will either stay on or turn on/off (see explanation in the images).
Switches up to 12VDC/35A. In stock -
Rocker Snap-In On/Off Light Switch ASW-17D Yellow
Rocker switch for switching 12V lighting such as a fog light.
Depending on how the switch is connected, the LED will either stay on or turn on/off (see explanation in the images).
Switches up to 12VDC/35A. In stock -
Rocker Snap-In On/Off Light Switch ASW-17D Blue
Rocker switch for switching 12V lighting such as a fog light.
Depending on how the switch is connected, the LED will either stay on or turn on/off (see explanation in the images).
Switches up to 12VDC/35A. In stock -
Scale division for potentiometers 0-100 41mm
Aluminum plate with a scale for potentiometers. The scale runs from 0 to 100.
Diameter: 41mm
In stock -
Micro switch / joystick 4-way with push button
This microswitch moves in four directions and also has a push-button function. This makes it ideal for switching operations that require menu navigation, for example.
Each direction and the push button has its own pin that you can connect to your microcontroller, such as an Arduino, Raspberry Pi or ESP.
-
Infrared/IR reflection sensor (Line follower) analog TCRT5000 3-way
This triple infrared reflectance sensor is ideal for line-following robots and other sensing applications. Thanks to its TCRT5000 sensors, the module offers high sensitivity, reliable performance, and strong resistance to interference.
Specifications:
- Operating voltage: 5V
- Sensor: TCRT5000 infrared reflection sensor
- Outputs (left, center, ri... In stock -
Housing Universal ABS 80x38x22mm black
Universal black ABS enclosure for housing electronics projects.
- With 2 mounting eyes and 3 cable entries.
- Clicks together easily.
Dimensions:
- external ~80x38x22mm (without eyes ~65x38x22)
- internal ~60x34mm In stock -
Voltage regulator 5 Volt / 2.2A - CDIL LM7805
5 Volt LM7805 voltage regulator.
The input voltage of 7 to 20 volts is reduced to 5 volts. This way, it doesn't matter what kind of power supply you have; with this voltage regulator, you always have 5V.
For example, for your Arduino sensors. For additional stabilization, it's recommended to connect two 10uF capacitors to the input and output (see ... In stock -
Solder Lead-free Sn96.5/Ag3/Cu0.5 1mm 10g - ECO4
Lead-free solder/solder wire in handy storage tube.
Specifications:
- Material: Tin (Sn): 96.5% / Silver (Ag): 3% / Copper (Cu): 0.5%
- Weight: 10gr
- Ø: 1.0mm
- Core: resin
- Melting point: 217°C-220°C
- Type: ECO4 In stock -
Developer universal jar 110g
For developing the photolayer of PCBs / printed circuit boards.
110g jar, enough to make 1500ml of developer.
Dissolve the contents of the sachet in water at 50°C. Allow the liquid to cool to room temperature (20°C). Then gently move the printed circuit board in the liquid to develop. Rinse under running water and dry carefully if necessary.
Prep... In stock -
Joystick Cross Rocker Monolever Momentary Switch
This momentary joystick switch features two normally open (2NO) contacts and automatically returns to the neutral position when the lever is released. Thanks to its robust rubber cover, the joystick is protected against water, oil, and dust (IP55), making it ideal for use in demanding environments.
Widely used in industrial control systems for swi... In stock -
Joystick Cross Rocker Monolever Tuimelschakelaar
Deze vergrendelende joystickschakelaar is voorzien van twee normaal open contacten (2NO) en blijft in de gekozen positie staan totdat deze handmatig wordt teruggeschakeld. Dankzij de robuuste rubberen hoes is de joystick beschermd tegen water, olie en stof (IP55), waardoor hij uitstekend geschikt is voor gebruik in veeleisende industriële omgeving...
In stock
-
Audio amplifier Bluetooth Audio player XY-P15W 30W stereo with housing
This compact Bluetooth amplifier module is ideal for DIY projects, speaker construction, and hobby electronics. With Bluetooth 5.0, stereo output, and up to 2x30 watts of power, the module delivers clear and powerful sound in a compact package.
Features:
- Bluetooth 5.0 for a stable wireless connection (up to 15 m range)
- Stereo output (2 channel... In stock -
Crimping pliers for wire end sleeves 0.25-10 mm² HSC8 6-4
This professional HSC8 crimping tool is specially designed for fast, reliable, and effortless crimping of wire end ferrules. Its ergonomic design and sturdy construction make it ideal for both hobbyists and professional installers.
- Suitable for wire end ferrules: 0.25 – 10 mm² (AWG 23~7)
- Precision crimping: Ensures a strong, durable connect... In stock -
OBD2 Extension cable male/female 1m
This OBD2 extension cable is ideal for extending or relocating the OBD port in your vehicle. Thanks to its ultra-thin, flat design, the cable can be easily concealed, even in tight spaces, without hindering safe driving.
Specifications:
- International standard 16-pin OBD2 socket
- 8-wire wiring, 9-pin power
Length: ~100cm In stock -
LED 5mm Red Flat Top
Red LED with a diameter of 5mm and a flat head (flat top).
These LEDs can be mounted flush with a surface, creating a sleek design.
Voltage: 2.3V
Current: 20mA
Brightness: 500~1500 mcd
Grid spacing: 2.54mm
-
Solar panel/solar cell 5V 380mA / 5W with USB connection
Simple solar panel with a USB 2.0 connection, for example for powering a small circuit or charging a telephone or battery.
Voltage: 5V
Power: 380mA
Dimensions: 88x142mm -
Step drill HSS with hexagonal shaft 3-12 mm
This high-quality HSS step drill bit is ideal for precise and gradual drilling of holes in plastic enclosures, project boxes and panels.
Thanks to the 10 steps (3 to 12 mm) you can easily create different hole diameters without having to change the drill every time.
The 1/4" hex shank provides a stable grip in cordless drills. A must-have tool for... In stock -
Ultimate Zero - RP2040 - ZERO - USB-C
The RP2040 is a powerful and versatile microcontroller designed for Raspberry Pi, ideal for embedded projects, prototyping, and educational purposes. This compact module features a powerful dual-core ARM Cortex-M0+ processor and offers excellent flexibility for both hobbyists and professionals.
The realistic "stamp hole" design makes the module ea... In stock -
LED Board Flexible 16x16 WS2812B 5050 RGB LED with drivers (256bits)
Flexible LED board with 16x16 WS2812B RGB LEDs. The board is slightly bendable.
All LEDs can be controlled individually (on/off, color and brightness)
over 1 data line with, for example, an ESP8266/ESP32 or Arduino.
With 2 combined data-in/out/power connections and 1 separate power connection.
Dimensions: 160mm x 160mm x 1.9mm (incl. LEDs)
Volt... In stock -
Universal acrylic housing 71x106x41mm transparent
Handy universal transparent acrylic housing for housing electronic circuits.
With slots for placing printed circuit boards.
Width: 71mm
Length: 106mm
Height: 41mm
color: transparent
See the drawings in the PDF for all dimensions. In stock -
ESP32-S3 Development Board WiFi/Buetooth - N16R8 XiaoZhi Balll Batt/Touch
ESP32-S3 N16R8 in ball shape with built-in speaker, microphone, 1.28 inch touchscreen and battery.
Powerful ESP32-S3 board with 16MB external flash, 8MB PSRAM 384K ROM and 512K built-in SRAM.
This ESP32 is ideally suited for creating a voice assistant with, for example, Home Assistant in combination with ESP Home.
Configuration for ESP Home:
htt... -
IDC Socket ribbon cable connector 2.54mm 2x20 pins
This 40-pin IDC connector from NELTRON is a reliable solution for quickly and securely connecting ribbon cables in a variety of electronic applications. Its 2x20-pin configuration with a 2.54mm pitch makes it compatible with standard headers, such as those found on Raspberry Pis, development boards, or industrial controllers.
Thanks to its selecti... In stock -
Stepstick TMC2225 V1.1 stepper motor driver for 3D printers
The TMC2225 is the ideal successor to the popular TMC2208 stepper driver. It delivers the same performance, but with improved heat dissipation thanks to its HTSSOP enclosure. This makes the TMC2225 not only quieter but also more durable under intensive use.
Thanks to its simple UART configuration (via jumper caps instead of soldering), this driver... In stock -
Stepper motor driver stepstick TMC2209 V2 for 3D printers UART
TMC2209 Stepper Driver – Ultra Quiet and Powerful (MKS Compatible)
Upgrade your 3D printer with the TMC2209 stepper driver – the silent powerhouse for precise and whisper-quiet motion. This driver is the perfect replacement for the TMC2208 and offers higher current capacity, improved cooling, and support for jumper-free UART control (ideal for ... In stock -
Buck converter Step Up DC-DC Uin:0.8V-3.3V Uout:3.3V
Very small power supply module for energy-efficiently increasing a supply voltage.
Supplied without header pins (see additional items).
The input voltage may be between 0.8 and 3.3 Volts.
The output voltage is fixed at 3.3V.
Input voltage: 0.8V-3.3V
Output voltage: 3.3V (+/-4%)
The power supplied depends on the input voltage:
- Input 1-1.5V, Out... In stock -
Test lead set with banana to crocodile clips black/red 1 meter
The crocodile clips easily connect to the points you want to measure and the other end fits into your multimeter or power supply!
Suitable for almost all multimeters.
Length: 1 meter
Set of black and red cable. In stock -
Battery tester XH-M239 for 18650 batteries
This versatile battery tester is designed to simultaneously monitor the voltage (V), current (A), capacity (mAh), time (h), and power (W) of a single 18650 lithium-ion battery. Ideal for testing and evaluating battery performance.
NOTE! The display is mostly in Chinese (see the manual for an explanation and what it looks like). (Since the text is ... -
Breakout adapter board for SWD cable (2x5 1.27mm) - Adafruit 2743
This adapter board is designed to make it easier to use ARM dev boards that use slimmer 2x5 (0.05"/1.27mm pitch) SWD cables for programming.
It's helpful for using products like the JTAGulator, STLink or SEGGER J-Link with tiny boards that use the 10-pin SWD programming connector, often Cortex M0 or M3's.
This board comes with no cables. It's r... Adafruit Part number: 2743 -
Strain relief Ø3.5mm x 12mm black
This elastomeric cable entry provides reliable strain relief for round cables. Its flexible design protects cables from sharp edges and stresses at the connection point.
Specifications:
- Application: round cables
- Hole diameter: 3.5 mm
- Material: elastomer (flexible)
- Color: black
- Length: 25 mm
- Max. panel thickness: 2.5 mm
Ideal for panel... In stock -
Breakout/Adapter board for ATMega328P IC
Breakout/adapter board for ATmega328P ICs, for example, to build your own Arduino.
In stock -
Electromagnet / Solenoid actuator - holding magnet 12V - 25kg
When activated, the magnet attracts a metal magnetic surface and holds it up to 25kg.
Dimensions: ⋄ 32mm x 25mm
Contact area: 16mm
Voltage: 12VDC
Current: 0.3A / 3.5W
Pulling force: 25kg
Thread: M5x12 In stock -
LilyPad Power Booster 5V for AAA battery
This small but powerful power module is specifically designed for portable LilyPad projects. Simply insert a AAA battery, flip the switch, and you'll get a stable 5V output—ideal for powering LilyPad circuits up to 200mA. The module is short-circuit protected and remarkably compact, allowing it to be discreetly incorporated into clothing or fabri...
In stock
-
Buck converter Step Down DC-DCUin:6-24V Uout:5 3A
This compact buck converter is an efficient and powerful solution for converting a higher DC input voltage (6–24V) to a stable 5V output voltage, ideal for powering USB devices. With a maximum output current of 3A and an impressive efficiency of up to 97.5%, this module delivers reliable performance in a small package.
The converter features bui... In stock -
Cable gland with strain relief M12 IP68 polyamide black
With this cable gland you can create a waterproof cable connection (IP67).
By tightening the nut a rubber seal is created around the cable, preventing any moisture from entering.
Suitable for cable diameters from 3.5mm to 7mm.
Resistant to UV radiation, therefore suitable for outdoor use.
Thread: M12 x 1.5
Thread length: 8mm
Material: polyamide
Ra... In stock -
USB Extension Cable USB-A Male-Female 60cm White
This cable extends any USB cable. Handy if you have to dive behind your computer every time you need to connect something!
Plug in this cable and place the end on your workstation so you can easily connect all of your USB devices.
Connectors: Type A male Type A female
Length: 60 cm (5 meters shown)
Color: white
In stock -
USB Verlengkabel USB-A male-female 1,5 meter
Met deze kabel verleng je iedere USB-kabel. Handig voor als je elke keer achter je computer moet duiken om iets aan te sluiten!
Sluit deze kabel aan en leg het uiteinde op je werkplek zodat je gemakkelijk al je USB-apparaten kunt aansluiten.
Connectors: Type A male Type A female
Lengte: 1,5 meter (afgebeeld 5 meter) -
Foot switch - CNTD CFS-1
Solid foot switch with normally open and normally closed contact.
After pressing, the switch automatically returns to its original position (self-resetting).
Switches up to: 10A/250V
Cord length: ~180cm -
Arduino Starter Kit UNO R3 Large
Extra large Arduino UNO starter kit with everything and more you need for a good start with the Arduino.
Contents:
- 1x Storage box
- 1x Arduino UNO (compatible) with USB cable
- 1x DC motor
- 1x 7-segment display 1 digit
- 1x 7-segment display 4 digits
- 1x Vibration sensor
- 1x Touch sensor
- 1x Stepper motor 28BYJ-48 with ULN2003 driver board
-... In stock -
Housing Universal ABS (splash) waterproof IP65 115x65x40mm gray G304
These enclosures consist of high-impact ABS (operating temperature : -20°C to +100°C).
The lid and the base are equipped with a tongue and groove sealing system with a neoprene gasket. The mounting holes and the lid-fixing screws are located outside the sealed area, preventing moisture and dust from entering the enclosure. Internal guide slots al... In stock -
Cable tester with tone generator UNI-T UT682D
UNI-T cable tester for detecting cables and possible breaks.
Method: Use both the tone generator and the probe to determine where a cable goes and see if it is broken (and if so, where the break is located).
You attach the tone generator to a wire with the crocodile clip and use the measuring probe to follow the wire (the measuring probe will bee... In stock -
Soldering iron 30W with LED lighting
This 30-watt soldering iron with LED lighting is the perfect choice for both hobbyists and professionals seeking precision, comfort, and reliability. Thanks to the integrated bright LED lighting, you always have a clear view of your workpiece, even in low-light conditions – ideal for fine soldering or dark workspaces.
With a powerful 30W heating... In stock -
Soldering station adjustable ceramic 48 Watts 150°C - 450°C Ohmeron
This soldering station is designed to meet all your soldering needs, with a wide temperature range of 150 to 450 degrees Celsius. This allows you to perform a wide variety of soldering tasks, from fine electronics work to soldering larger components.
The soldering station operates on a 230VAC/50Hz power supply and features a soldering iron with a ... In stock -
MOSFET PWM Module 400W/15A
This PWM MOSFET Trigger Switch Module (400W, 15A) is designed to control powerful electronic loads such as DC motors, pumps, LED lighting and electromagnetic valves.
The module uses two high-power MOSFETs in parallel, which ensures low resistance, high current capacity and reliable performance up to 15A and 400W at room temperature.
It supports a ... In stock -
USB Adapter board
With this board you can connect all different types of USB connectors to each other.
It has USB-A male and female connections, a USB-C connection and a MicroUSB connection.
You can also solder header pins on it to connect your own cabling. In stock -
Display OLED 128x64 1.3 Inch I2C White
This white OLED display (128x64 pixels) is a compact and energy-efficient screen with a high resolution and wide viewing angle. Thanks to the built-in SH1106 driver chip (compatible with SSD1306), it offers excellent display quality under almost all conditions.
The display operates at both 3.3V and 5V and supports multiple communication modes incl... In stock -
Display OLED 128x64 1.3 Inch I2C Blue
This blue OLED display (128x64 pixels) is a compact and energy-efficient screen with a high resolution and wide viewing angle. Thanks to the built-in SH1106 driver chip (compatible with SSD1306), it offers excellent display quality under almost all conditions.
The display operates at both 3.3V and 5V and supports multiple communication modes inclu... In stock -
Vibration motor Type 370 6V 8500rpm single round
This type 370 motor (6V, 8500RPM) is a powerful, compact vibration motor that is suitable for various applications such as massage equipment, toys, alarm and warning systems.
This motor features a single, round eccentric head for a balanced and effective vibration.
Voltage: 6VDC
RPM: 8500
-
Vibration motor Type 370 6V 6000rpm double round
This type 370 motor (6V, 6000RPM) is a powerful, compact vibration motor that is suitable for various applications such as massage equipment, toys, alarm and warning systems.
This motor features a double-sided, round eccentric head for a balanced and effective vibration.
Voltage: 6VDC
Speed: 6000
In stock -
Vibration motor Type 370 6V 3000rpm single sector
This type 370 motor (6V, 3000RPM) is a powerful, compact vibration motor that is suitable for various applications such as massage equipment, toys, alarm and warning systems.
This motor features a single, sector-shaped eccentric head for a balanced and effective vibration.
Voltage: 6VDC
Speed: 3000
In stock -
Vibration motor Type 370 6V 3000rpm double sector
This type 370 motor (6V, 3000RPM) is a powerful, compact vibration motor that is suitable for various applications such as massage equipment, toys, alarm and warning systems.
This motor features a double-sided, sector-shaped eccentric head for a balanced and effective vibration.
Voltage: 6VDC
Speed: 3000
In stock -
Buck converter Step Down 5V Uin:6-40V Uout:5V 3A with 2 USB connectors
This DC-DC step-down converter (with LM2596 chip) efficiently converts an input voltage of 6V~40V to 5V/3A, ideal for charging USB devices. The module features two USB outputs and provides enough power to power two mobile devices simultaneously. With a maximum efficiency of 92% and a compact size, it is an excellent solution for in-vehicle use, mob...
In stock
-
Gas sensor MQ-138 (Formaldehyde)
The MQ-138 is a versatile gas sensor designed to detect formaldehyde, benzene, alcohols, ketones and other volatile organic compounds (VOCs). This sensor provides both a digital TTL output and an analog voltage output (0–5V), and is easily integrated with microcontrollers such as Arduino or other development boards.
Thanks to its wide detection ... In stock -
Gas sensor MQ-137 (Ammonia)
The MQ-137 is a gas sensor specifically designed for the detection of ammonia (NH₃) and other organic amines, such as trimethylamine and ethanolamine. Due to its high sensitivity and reliability, this sensor is ideally suited for air quality measurements in industrial, agricultural or educational applications.
The sensor module provides both an ... In stock -
Gas sensor MQ-136 (Hydrogen sulfide sensor (H₂S))
The MQ-136 is a compact sensor for detecting hydrogen sulfide (H₂S) and other harmful gases such as LPG, butane, methane, smoke and alcohol. Due to its high sensitivity and fast response time, this sensor is ideally suited for applications in gas leak detection, air quality monitoring and safety monitoring.
The module has an analog output and a ... -
Gas sensor MQ-131 (Ozone, Chlorine, CO2)
The MQ-131 ozone sensor is a compact and powerful sensor for detecting ozone gas (O₃) in the air. The sensor uses tin oxide (SnO₂) as a sensitive material, which responds to the presence of ozone by increasing its conductivity. This change can be easily converted into a readable signal corresponding to the ozone concentration.
The sensor has a... In stock -
Loudspeaker Chassis / Terminal rectangular single
Suitable for wire from AWG 24 to 16.
In stock
-
Loudspeaker Chassis / Terminal rectangular double
Suitable for wire from AWG 24 to 16.
-
Muscle sensor / EMG sensor AD8232
This EMG muscle electrical sensor kit with AD8232 module is designed to accurately measure muscle activity (EMG signals). The kit includes electrode pads, a 3.5mm cable and a microcontroller-compatible breakout board.
Thanks to its small size (25.5 mm) and standardized breadboard design, the module is ideal for applications in robotics, prosthetics... In stock -
Servo motor driver/ PWM 16 channel 12 bits PCA9685 I2C
This 16-channel PWM servo driver based on the PCA9685 chip makes it easy to precisely control multiple servos or LEDs via I2C. Thanks to 12-bit resolution and an external power supply up to 6V, it is ideal for robotics, lighting and embedded projects. Works with Arduino, Raspberry Pi and other microcontrollers.
Supplied fully soldered as shown.
-... In stock -
Distance sensor Laser - Time of Flight - VL6180X/TOF050C - 50cm
The TOF050C is a compact Time‑of‑Flight (ToF) sensor based on the STMicroelectronics VL6180 chip, designed for accurate distance measurement up to 50 cm. It features FlightSense™ technology that provides reliable dimensions regardless of the color or texture of the object
Key Features:
- Measuring range: 2–50 cm (dead zone 0–2 cm)
- Ope... In stock -
Distance sensor Laser - Time of Flight - VL53L1/TOF400C - 400cm
The VL53L1 (integrated in the TOF400C breakout board) is an advanced Time-of-Flight (ToF) distance sensor based on STMicroelectronics' VL53L1X chip. This sensor uses FlightSense™ technology with a 940 nm infrared laser (Class 1) and a SPAD detector array to achieve accurate absolute distance measurements up to 4 meters (400 cm), independent of co...
In stock
-
Distance sensor Laser - Time of Flight - VL53L0/TOF200C - 200cm
The VL53L0X is a compact and accurate Time‑of‑Flight distance sensor integrated into the TOF200C breakout board. Featuring STMicroelectronics' advanced FlightSense™ technology, the sensor accurately measures distances up to 200 cm, regardless of the reflectance or color of the object.
Key Features:
- Measuring range: 3 cm – 200 cm (dead z... In stock -
Fine dust / Dust sensor - PMS5003 PM2.5
The PMS5003 is a high-precision laser dust sensor designed to measure the concentration of fine dust particles in the air, including PM1.0, PM2.5 and PM10.
The sensor uses laser scattering technology to reliably detect particles ranging in size from 0.3 to 10 micrometers.
Its compact size of 50mm×38mm×21mm makes it easy to integrate into various ... In stock -
Fine dust / Dust sensor - PMS3003 PM2.5
The PMS3003 is a reliable laser dust sensor designed for measuring the concentration of fine dust particles in the air, with specific attention to PM1.0, PM2.5 and PM10.
The sensor detects particles with a size between 0.3 and 10 micrometers and is therefore very suitable for air quality monitoring in indoor environments.
With dimensions of 50mm×4... -
Fine dust / Dust sensor - PMS7003 PM2.5
The PMS7003 is a compact laser dust sensor that accurately measures the concentration of fine dust particles in the air, including PM1.0, PM2.5 and PM10.
With a measuring range of 0.3 to 10 micrometers and using advanced laser scattering technology, the sensor provides reliable air quality data.
Its small size of 38mm×35mm×12mm makes it ideal for... In stock -
Fine Dust / Dust Sensor - PMSA003 PM2.5
The PMSA003 is a compact and accurate PM2.5 laser dust sensor designed for measuring the concentration of airborne particles such as PM1.0, PM2.5 and PM10. Measuring only 38mm×35mm×12mm, this sensor is ideal for applications where space is limited.
It operates on a supply voltage of 5V and functions reliably within a temperature range of -10°C t... In stock -
Weight sensor / Weigh cell / Load cell Bar 5kg
This micro load cell is a compact and accurate weight sensor with a maximum capacity of 5 kg. With an output sensitivity of 1.0 mV/V, low deviation, and a robust metal housing, it is ideal for applications such as electronic scales or measurement projects.
The sensor operates within a temperature range of -10 to +50°C, has high insulation resistan... In stock -
Weight sensor / Weigh cell / Load cell Bar 20kg
This micro load cell is a compact and accurate weight sensor with a maximum capacity of 20 kg. With an output sensitivity of 1.0 mV/V, low deviation, and a robust metal housing, it is ideal for applications such as electronic scales or measurement projects.
The sensor operates within a temperature range of -10 to +50°C, has high insulation resista... In stock -
Weight sensor / Weigh cell / Load cell Bar 1kg
This micro load cell is a compact and accurate weight sensor with a maximum capacity of 1 kg. With an output sensitivity of 1.0 mV/V, low deviation, and a robust metal housing, it is ideal for applications such as electronic scales or measurement projects.
The sensor operates within a temperature range of -10 to +50°C, has high insulation resistan... In stock -
Weight sensor / Weigh cell / Load cell Bar 10kg
This micro load cell is a compact and accurate weight sensor with a maximum capacity of 10 kg. With an output sensitivity of 1.0 mV/V, low deviation, and a robust metal housing, it is ideal for applications such as electronic scales or measurement projects.
The sensor operates within a temperature range of -10 to +50°C, has high insulation resista... In stock -
Temperature and humidity sensor AHT21 + Air quality sensor ENS160
The ENS160 is a digital multi-gas sensor designed for indoor air quality measurement and detects a wide range of gases such as toluene, hydrogen, ethanol, NO₂ and ozone. Ideal for applications in smart home, building automation, air purification and consumer electronics.
In stock
The AHT21 sensor is a new generation temperature and humidity sensor in ... -
Gas sensor/Air quality sensor AGS10 TVOC I2C
The AGS10 is a compact MEMS sensor for measuring TVOC (Total Volatile Organic Compounds) via digital I²C communication. Thanks to low power consumption, high sensitivity and simple control, this sensor module is ideal for smart air quality projects.
In stock
Specifications:
Supply voltage: 3.0–6.0V
Typical consumption: 75 mW
Interface: I²C (slav... -
Relay board with light sensor XH-M131 12V
This module is designed for automatic switching of electrical devices based on light intensity. The light sensitivity is adjustable via a potentiometer. Ideal for applications such as automatic lighting or day/night controlled switching.
Features:
- Input voltage: DC 12V (with reverse polarity protection)
- Relay switching capacity:
- AC: 0–12... In stock -
Power connectors MR30 male+female 15A 3pins
This MR30 connector set consists of a male and female plug and is ideal for compact, high-current connections in RC applications, drones, batteries and other electronics.
Features:
- Nominal current: 15A
- Peak current: up to 30A
- Voltage: suitable for DC applications
- Insulation material: high-quality heat-resistant PA
- Temperature range: -20�... In stock -
Arduino MEGA 2560 + ESP8266 WiFi Development Board – 2-in-1 Mega R3+
This powerful 2-in-1 development board combines an ATmega2560 (Mega R3) microcontroller with an onboard ESP8266 WiFi module, providing a versatile platform for IoT and embedded projects. Both chips can be used independently or simultaneously, each with their own pin headers. Ideal for applications that require both extensive I/O and wireless commun...
In stock
-
Motion sensor/detector mmWave HLK-LD2420
The LD2420 is an extremely sensitive 24GHz millimeter wave radar module for detecting human presence, movement and micromovement. Thanks to FMCW technology and a built-in intelligent algorithm, this sensor is ideal for smart automation in indoor spaces such as offices, homes or home automation projects.
Detection principle: FMCW continuous wave ra... In stock -
ESP32-C3 Mini-1 Development Board WiFi/Buetooth
Compact and powerful ESP32-C3 development board with WiFi and Bluetooth Low Energy (BLE). Based on the ESP32-C3FH4 or ESP32-C3FN4 chip with 32-bit RISC-V core at 160 MHz. Ideal for wireless IoT projects, smart devices and embedded applications. Equipped with USB interface for power, programming and communication.
Chip: ESP32-C3 (RISC-V, single cor... In stock -
Housing Universal ABS 77x55x30mm
Compact ABS housing for electronics projects. Equipped with ventilation slots which makes this housing suitable for sensors.
Dimensions: 77x55x30mm In stock -
Digital sliding caliper 150mm 0.01mm resolution stainless steel
Precision digital caliper made of stainless steel (4CR13), suitable for measuring outside and inside diameters, depths and steps. With a resolution of 0.01mm and a measuring accuracy of ±0.03mm, ideal for precise measurements in the workshop or electronics environment.
Specifications:
- Measuring range: 0–150 mm
- Resolution: 0.01 mm
- Accuracy... In stock -
Ball bearing 6001-2Z 28x12x8mm SKF
Double shielded ball bearing 6001-2Z from SKF.
Outer diameter: 28mm
Inner diameter: 12mm
Thickness/Width: 8mm In stock -
Ball bearing 608-2Z 22x8x7mm SKF
Double shielded ball bearing 608-2Z from SKF.
Outer diameter: 22mm
Inner diameter: 8mm
Thickness/Width: 7mm In stock -
Ball bearing 623-2Z 10x3x4mm SKF
Double shielded ball bearing 623-2Z from SKF.
Outer diameter: 10mm
Inner diameter: 3mm
Thickness/Width: 4mm In stock -
Touch/touch sensor capacitive 3x4 MPR121
The MPR121 is a compact capacitive touch controller with I2C interface, ideal for building touch-sensitive interfaces in electronic projects.
This sensor has 3x4 touch sensitive pads and operates on 3.3V.
Because this keypad works with I2C you only need 1 pin on your microcontroller (Arduino/ESP/Raspberry Pi).
There are several libraries for Ardui... In stock -
Membrane keypad 4x1 red/3xyellow/green for Arduino
Keypad with one red, 3 yellow and one green button.
With self-adhesive back.
Dimensions: 20x106x1mm
Button diameter: 11.5mm
Cable length: approx. 95mm. In stock -
Membrane keypad 1x4 red/yellow/yellow/green for e.g. Arduino
Keypad with one red, 2 yellow and one green button.
With self-adhesive back.
Dimensions: 20x150x1mm
Diameter buttons: 11.5mm
Cable length: approx. 95mm. In stock -
Membrane keypad 1x4 blue for e.g. Arduino
Keypad with 4 blue buttons in a row.
With self-adhesive back.
Dimensions: 106x16x1mm
Diameter buttons: 10mm
Cable length: approx. 90mm. In stock -
Membrane keypad 1x1 green for e.g. Arduino
Keypad with 1 green button.
With self-adhesive back.
Dimensions: 20x23x1mm
Diameter buttons: 11.5mm
Cable length: approx. 90mm. In stock -
Membrane keypad 1x1 red for e.g. Arduino
Keypad with 1 red button.
With self-adhesive back.
Dimensions: 20x23x1mm
Diameter buttons: 11.5mm
Cable length: approx. 90mm. In stock -
Membrane keypad 1x1 gray for e.g. Arduino
Keypad with 1 gray button.
With self-adhesive back.
Dimensions: 20x23x1mm
Diameter buttons: 11.5mm
Cable length: approx. 90mm. In stock -
Membrane keypad 1x1 yellow for e.g. Arduino
Keypad with 1 yellow button.
With self-adhesive back.
Dimensions: 20x23x1mm
Diameter buttons: 11.5mm
Cable length: approx. 90mm. In stock -
LED 5mm Blue Matte pre-wired for 5V-9V
Blue 5mm LED with frosted lens and pre-wired with built-in resistor for use on 5V-9V.
Cable length: ~20cm In stock -
LED 5mm Red Matte pre-wired for 5V-9V
Red 5mm LED with frosted lens and pre-wired with built-in resistor for use on 5V-9V.
Cable length: ~20cm In stock -
LED 5mm Green Matte pre-wired for 5V-9V
Green 5mm LED with frosted lens and pre-wired with built-in resistor for use on 5V-9V.
Cable length: ~20cm In stock -
LED 5mm Yellow Matte pre-wired for 5V-9V
Yellow 5mm LED with frosted lens and pre-wired with built-in resistor for use on 5V-9V.
Cable length: ~20cm In stock -
ATtiny85 USB Developer Board USB-C
Super small 'Arduino' board with USB-C connector.
This board is based on the ATtiny85 microcontroller which is similar to the chips used for Arduinos. The ATtiny85 can be programmed with the Arduino program (IDE).
The board can be powered by the USB connection or by an external power supply (7-35V) on Vin. The built-in voltage regulator (5V/500mA)... In stock -
Prototyping board for Arduino UNO
This Arduino UNO prototyping board makes it easy to design custom circuits for your next Arduino project.
You can solder components onto the prototyping area to build your project, or use it with a small solderless breadboard (not included) to quickly test circuit ideas without having to solder.
It has extra connections for all Arduino I/O pins an... -
Transistor N-MOSFET IRF540 single board
Board with an IRF540 mosfet for controlling motors, LEDs, etc.
With screw terminals and header pin connections.
MOSFETs have good switching characteristics and are widely used to control almost any DC load. This is a 1-channel MOSFET switch and uses the very popular IRF540 MOSFET. It is perfect for switching DC loads up to 10A.
The module is opto-... In stock -
Arduino practice and experimenting shield with display
Experiment shield with display for the Arduino UNO or Mega.
The shield is perfect if you want to learn how an Arduino works and how to program it.
The shield contains the following modules:
- display with 74HC595 driver
- reset button
- buzzer
- 3 microswitch buttons
- 4 LEDs
- potentiometer 3296
- header pins for sensors and servos
In stock -
Power supply module multi 6V-12V to 3.3V and 5V with switch (800mA)
Handy voltage converter with three fixed output voltages: 3.3V, 5V, and 12V. Ideal for powering multiple components within a single project, such as sensors, microcontrollers, or modules with varying voltage requirements. Operates on an input voltage of 6V to 12V (note: the input voltage must be at least 1V higher than the desired output).
Input v... In stock -
Touch switch/sensor Capacitive MPR121 Breakout I2C - 12 Channels
The MPR121 is a compact capacitive touch controller with I2C interface, ideal for building touch-sensitive interfaces in electronic projects. The module supports up to 12 individual touch electrodes plus a virtual thirteenth electrode. In addition, 8 pins are available for directly driving LEDs (when they are not used as electrodes).
Perfect for a... In stock -
Audio amplifier Bluetooth Audio player MP3 50W stereo 6-18V
Multifunctional Bluetooth 5.0 decoder module for playing music via USB, TF card, Bluetooth, AUX and FM radio.
Supports various audio formats and provides useful functions such as remote control, automatic input switching and power failure memory. Ideal for DIY audio projects, speakers or car audio upgrades.
Specifications:
- Supply voltage: 6V �... In stock -
Power supply board with DC5.5/2.1mm jack plug
Handy breakout board for connecting a power supply with DC5.5/2.1mm jack plug to, for example, a breadboard or a circuit.
You get 2 header pins with Vcc connection, and 2 GND connections.
(Excluding power supply.) In stock -
Buck converter Step Down5V Uin:6-40V Uout:5V 3A with 2 USB connectors
Compact and efficient buck converter with dual USB output. Converts an input voltage of 6V to 40V to a stable 5V output with a maximum current of 3A. Suitable for simultaneously charging two devices such as smartphones or tablets or for powering electronic projects.
Equipped with Apple recognition resistance for optimal compatibility.
Ideal for mob... In stock -
ATX PC computer power adapter small with housing
Adapter that you can connect to an ATX computer power supply with a 24-pin connector.
The adapter with on/off switch provides you with 3 different output voltages/terminals: -12V / +12V / +5V / +3.3V.
- With 2 USB-A connections.
- With on/off switch.
- With a fuse for each voltage.
- Delivered fully assembled, you only need to assemble the housing... In stock -
Soldering station adjustable 90W / 200-480°C Bakon BK90
Robust 90 watt soldering station with temperature setting from 200°C to 480°C. Suitable for lead-free soldering, among other things. With a fine soldering tip for all soldering work.
Features:
- Large LED screen with beautiful interface.
- High heating speed with new updated PCB circuit design.
- Stable temperature due to microcomputer control.... In stock -
Adjustable 2-in-1 soldering station with 60W soldering iron and 300W hot ai
Soldering with precision? This 2-in-1 soldering station makes it easy. The 60 W soldering iron is perfect for finer work, while the 300 W hot air pump effortlessly removes SMD components. The microprocessor-controlled temperature control keeps the heat stable: 50-480 °C for the soldering iron and 100-500 °C for the hot air function. Thanks to the...
In stock
-
Spare tip for Velleman VTSS220 soldering stations - 0.2mm
Ensure excellent precision in every soldering project with this 0.2mm replacement soldering tip, perfectly matching the Velleman soldering station EAN5410329682194. This pointed soldering tip is ideal for fine and precise soldering, ensuring reliable connections in every application.
- Wear-resistant: This soldering tip is robustly designed for fr... In stock -
Spare tip for Velleman VTSSC74 soldering stations - 3.2mm
Spare tip / soldering tip BIT74/3 for Velleman VTSSC74 soldering stations.
This point has a width of 3.2mm (chisel shape). In stock -
Wire stripper adjustable
This adjustable wire stripper is an indispensable tool for precise stripping. With adjustable cutting depth, this pliers is suitable for a wide range of wire diameters, from 0.2 mm to 3 mm. The red design not only exudes style, but also stands for durability. Whether you are a professional or a DIYer, this pliers offers reliability and precision fo...
In stock
-
Glass fuse 5x20mm 250mA fast 250VAC
Cylindrical glass fuse, 250mA, fast-acting. For nominal AC voltages up to 250V.
The dimensions of this fuse are 5x20mm.
For use in new equipment or repairing existing equipment.
In stock -
Soldering flux RF800 bottle with brush 50ml
Welcome to the world of hassle-free soldering with Flux RF800, the ideal solution, especially for your SMD (Surface Mount Device) soldering projects. Whether you're an experienced professional or an electronics enthusiast, Flux RF800 offers a revolutionary solution. It's the perfect soldering product, ensuring excellent connections and the highest ...
In stock
-
Fiberglass prototyping board / PCB (64x109 holes / 18x30cm)
Universal prototype PCB for making electronics projects.
Easily transfer your project from breadboard to this board!
With soldered holes on both sides.
Size: 18cm x 30cm x 1.4mm
Number of holes: 64 x 109
Hole size: 1mm.
Hole spacing: 2.54mm.
In stock -
Fiberglass prototyping board / PCB (46x65 holes / 12x18cm)
Universal prototype PCB for making electronics projects.
Easily transfer your project from breadboard to this board!
With soldered holes on both sides.
Size: 12cm x 18cm x 1mm
Number of holes: 46 x 65
Hole size: 1mm.
Hole spacing: 2.54mm. In stock -
Solder Lead-free Sn99.3/Cu0.7 Ø1mm tube 12g
Lead-free solder/solder wire in handy storage tube.
Specifications:
- Material: Tin (Sn): 99.3% / Copper (Cu): 0.7%
- Weight: 12gr
- Ø: 1.0mm
- Core: resin In stock -
Prototyping board for Arduino Nano
This Arduino Nano prototyping board makes it easy for you to design custom circuits for your next Arduino project.
You can solder parts to the prototyping area to create your project, or use it with a small solderless breadboard (not included) to quickly test circuit ideas without having to solder.
It's got extra connections for all of the Arduin... In stock -
Converter USB-C to Serial UART CH340E breakout 3.3V/5V
For easily connecting circuits/MCUs to a USB Type-C port. On a computer, the converter acts as a COM port and communicates via a serial connection.
With a GND, TXD, RXD, DTR, 3.3V and 5V pin.
With a power LED and TX/RX LED. In stock -
Button Boss Silver 20mm
For example for potentiometers with a 6mm shaft.
With mounting screw.
Diameter: 16-20mm
Height: 12mm
(Image of 27mm version.) In stock -
Ultrasonic miniature humidifier / mist maker - Atomizer 16mm/20mm
Loose atomizer element for the air humidifier / mist maker ultrasonic miniature.
Diameter without cover ~16mm.
Diameter in combination with cover ~20mm.
In stock -
Rocker switch snap-in on/off double SPST black
Two on/off rocker switches housed in a single housing. Easily clicks into a hole.
Maximum current: 3A/250V AC - 6A/125V AC
Connector dimensions: 4.8x0.8x8.4mm
In stock -
LED fitting/fixture 5mm transparent white
Transparent white LED holder/fitting/bezel for 5mm LEDs. The LED simply clicks into the holder.
Supplied without LED.
Hole Diameter: 6.4mm±0.5mm In stock -
LED fitting/fixture 5mm transparent red
Transparent red LED holder/fitting/bezel for 5mm LEDs. The LED simply clicks into the holder.
Supplied without LED.
Hole Diameter: 6.4mm±0.5mm In stock -
LED fitting/fixture 5mm transparent green
Transparent green LED holder/fitting/bezel for 5mm LEDs. The LED simply clicks into the holder.
Supplied without LED.
Hole Diameter: 6.4mm±0.5mm In stock -
LED fitting/fixture 5mm transparent blue
Transparent blue LED holder/fitting/bezel for 5mm LEDs. The LED simply clicks into the holder.
Supplied without LED.
Hole Diameter: 6.4mm±0.5mm In stock -
LED fitting/fixture 3mm transparent white
Transparent white LED holder/fitting/bezel for 3mm LEDs. The LED simply clicks into the holder.
Supplied without LED.
Hole diameter: 4mm±0.5mm In stock -
LED fitting/fixture 3mm transparent red
Transparent red LED holder/fitting/bezel for 3mm LEDs. The LED simply clicks into the holder.
Supplied without LED.
Hole diameter: 4mm±0.5mm In stock -
LED fitting/fixture 3mm transparent green
Transparent green LED holder/fitting/bezel for 3mm LEDs. The LED simply clicks into the holder.
Supplied without LED.
Hole diameter: 4mm±0.5mm In stock -
LED fitting/fixture 3mm transparent yellow
Transparent yellow LED holder/fitting/bezel for 3mm LEDs. The LED simply clicks into the holder.
Supplied without LED.
Hole diameter: 4mm±0.5mm In stock -
Thermal paste H sachet 0.5g
In today’s world, where electronics are becoming more advanced and devices are working under greater stress, effective heat dissipation becomes crucial. Enter Thermal Conductive Paste H, a product that primarily provides exceptional thermal conductivity above >0.88 W/mK, ensuring optimal cooling of your devices.
Why Thermally Conductive Paste H?... In stock -
Solder paste Easy Print Sn96.5/Ag3/Cu0.5 AGT-028 syringe 6g
Solder paste Easy Print Sn96.5Ag3Cu0.5 is an innovative agent used in the SMD soldering process.
This lead based solder paste is ideal for both automated soldering and manual printers.
This lead-free Easy Print solder paste is undoubtedly a reliable and versatile solution for everyone who values quality and efficiency in soldering processes. With ... In stock -
Wire 1x3.0mm² multi-stranded flexible core 5 meters black
A 5-meter roll of black-sheathed copper wire with a 3mm multi-stranded flexible core for use in electronics and other craft projects.
External: 4mm In stock -
Wire 1x3.0mm² multi-stranded flexible core 5 meters red
A 5-meter roll of red-coated copper wire with a 3mm multi-stranded flexible core for use in electronics and other craft projects.
External: 4mm In stock -
Zener diode set 0.5W 30 values - 300 pieces
Set of zener diodes in 30 values (10 pieces per value).
This set contains the following zener diodes.
10 pieces 2V0 - 2.0V (BZX55C2V0)
10 pieces 2V2 - 2.2V (BZX55C2V2)
10 pieces 2V4 - 2.4V (BZX55C2V4)
10 pieces 2V7 - 2.7V (BZX55C2V7)
10 pieces 3V0 - 3.0V (BZX55C3V0)
10 pieces 3V3 - 3.3V (BZX55C3V3)
10 pieces 3V6 - 3.6V (BZX55C3V6)
10 pieces 3V8 -... In stock -
Automatic temperature controller STC-1000 24VDC - Heating + cooling
Automatic temperature controller with 2 built-in relays for switching a cooling and heating system (up to 10A/250V).
With clear LCD display for displaying and setting the temperature.
- Controller power supply voltage: 24V DC
- Power consumption: In stock -
Automatic temperature controller STC-1000 230VAC - Heating + cooling
Automatic temperature controller with 2 built-in relays for switching a cooling and heating system (up to 10A/250V).
With clear LCD display for displaying and setting the temperature.
- Controller power supply voltage: 230V AC
- Power consumption: -
Tie-wrap cable tie 300x5mm black bag 250 pieces
Bag with 250 pieces of black tie-wrap cable ties 300x5mm.
Length: ~300mm
Width: 5mm
In stock -
SD Card Reader/Card Reader Breakout Board/Module SPI Mini
This mini SD Card module is a simple solution for reading/writing data from/to a microSD card (up to 2GB).
The pinout is directly compatible with the Arduino, but this module can also be used with other microcontrollers.
This allows you to add mass storage and data logging to your project.
Suitable for SD and SDHC cards (not included).
Easy to c... In stock -
Solder paste Easy Print Sn62/Pb36/Ag2 AGT-023 syringe 6g
Solder Paste Easy Print Sn62/Pb36/Ag2 is an innovative agent used in the SMD soldering process. Our lead-based solder paste is ideal for both automated soldering and manual printers.
Features:
High-quality ingredients: Easy Print contains 62% tin, 36% lead, and 2% silver, ensuring effective and durable solder joints. This composition guarantees r... In stock -
Soldering flux RF800 bottle 15ml
Welcome to the world of hassle-free soldering with Flux RF800, the ideal solution primarily for your SMD (Surface Mount Device) soldering projects. Whether you are an experienced professional or an electronics enthusiast, Flux RF800 offers a revolutionary solution. It is the perfect soldering product, ensuring excellent connections and the highest ...
In stock
-
Brass gear 11-tooth 0.5M for 2mm axle
Brass gear with 11 teeth modulo 0.5 for a 2mm shaft.
Shown as 8 teeth. In stock -
Ultrasonic Speaker Waterproof 5140 51mm
Waterproof ultrasonic speaker for repelling pests, dogs, and cats, among other things.
Diameter: 51mm In stock -
USB Power Cable USB to 5.5x2.1 jack plug (9VDC output)
With this cable you can get 9V from your USB connection to connect it to a circuit.
Voltage: 9VDC
Length: ~80cm
Plugs: USB-A -> 5.5x2.1 jack plug In stock -
Antistatic soldering mat with grounding cord 100x70cm mm gray
This large soldering mat ensures a clean and ESD-safe workspace during soldering. Made of flexible, acid-resistant rubber with good toughness and high elasticity, it comes with an ESD grounding cord.
With a heat resistance of up to 300°C, a non-slip surface and dimensions of 100x70cm, this mat is ideal for soldering work.
High-quality material: T... In stock -
End stop sensor optical
Optical end stop detection for any 3D printer or CNC machine.
- Optical end stop switch
- 3 pin cable (length +/- 100cm)
- Supply voltage: 2.7V ~ 5V
In stock -
Ultimate Pico - RP2040 - 16M - USB-C
Ultimate Pico with RP2040 microcontroller, 264KB SRAM and 16MB on-chip flash memory.
This Pico RP2040 is equipped with two powerful Cortex M0+ cores that can run up to 133 MHz and is compatible with the Raspberry Pi Pico.
With USB-C connection and loose header pins.
Dimensions: 52mm x 19mm In stock -
Seeed XIAO Microcontroller RP2040
Seeed Studio XIAO RP2040 is compatible with the Raspberry Pi RP2040 ecosystem as they share the same RP2040 chip. It supports multiple languages including C / MicroPython / CircuitPython. This will be a great tool for you to get started with MicroPython.
Specifications:
- CPU: Dual-core ARM Cortex M0+ processor, flexible clock running up to 133 M... In stock -
Motor DC JGA25-370 6V 1360rpm gear motor
6 Volt DC gear motor of the type JGA25-370 with a speed of 1360 rpm. This motor is suitable for heavier applications.
Voltage: 6VDC
Speed: 1360rpm
Motor Diameter: ~25mm
Axle diameter: 4mm (D-Axle)
Axle length: 12mm -
Motor DC JGA25-370 12V 620rpm gear motor
12 Volt DC gear motor of the type JGA25-370 with a speed of 620 rpm. This motor is suitable for heavier applications.
Voltage: 12VDC
Speed: 620rpm
Motor Diameter: ~25mm
Axle diameter: 4mm (D-Axle)
Axle length: 12mm -
Power supply module multi 3.3V and 5V with switch
Handy power module with 3.3 volt and 5 volt outputs. The input voltage may be between 6V and 24V (DC).
- With jack plug and terminal block connection for the input voltage.
- With on/off switch
- 2 sets of header pins for 3.3V and 5V
Specifications:
- Input voltage: 6V - 24V
- Output voltage: 5V (6 channels) + 3.3V (6 channels)
- Output current: 5... In stock -
Audio amplifier 3W stereo 2.0-5V HXJ8002
This miniature audio amplifier module is ideal for adding audio functions to your new project. It is based on the HXJ8002 single-channel 3W BTL audio amplifier chip, which provides low harmonic distortion to the audio signal.
Specifications:
- On-board HXJ8002 chip
- Number of channels: 1
- Output power: 3 W (for 3 Ω load), 2.5 W (4 Ω load), 1.... In stock -
ATX PC computer power adapter - case
Housing for 'ATX PC computer power supply adapter'.
Our version differs slightly from the images, as it also has cutouts for the fuses.
In stock -
Bluetooth Audio 5.0 Receiver
With this receiver you can play music from your phone or other Bluetooth audio player to speakers or headphones (with 3.5mm jack plug).
For example, if your amplifier does not have Bluetooth but does have an aux input to which you can connect a 3.5mm jack plug (possibly with a tulip to jack plug adapter cable), then this Bluetooth receiver is the s... In stock -
Fingerprint scanner AS608
This compact fingerprint scanner based on the AS608 chip can store up to 128 individual fingerprints.
There is an Adafruit library for this scanner so using it in combination with an Arduino or ESP is not too difficult.
Check out the link below for an extensive tutorial.
Voltage: 3.3V
Resolution: 500dpi
Supply current: In stock -
Speaker 8 Ohm 0.5 Watt Mini Metal - 20mm
A super small audio speaker ideal for radio and amplifier projects and small enough to build into a robot.
Features:
- Diameter: 20mm
- Power: 0.5W
- Impedance: 8 Ohm In stock -
Capacitor 1000µF 100V ±20% Electrolytic
In stock
-
Nut M12 polyamide 5mm black
M12 polyamide nut for, among other things, union nuts.
Thickness: 5mm
Key: 18mm
Urgency: 1.5
In stock -
Trimming knife - Spare blade
Spare blade for trimming knife.
In stock
-
Fitting for large E10 screw bulb
Metal lamp holder for E10 screw bulb with double lip with 2 holes for mounting. With 1 solder eye to attach a wire.
In stock -
Screwless terminal KF141R 2-way
Terminal for screwless clamping of wire from 26AWG to
18AWG.
- 2-fold
- type: KF141R (side insertion)
- pitch (distance between pins): 2.54mm
- strip the wire to 11mm In stock -
Screwless terminal KF141R 3-way
Terminal for screwless clamping of wire from 26AWG to
18AWG.
- 3-fold
- type: KF141R (side insertion)
- pitch (distance between pins): 2.54mm
- strip the wire to 11mm In stock -
Screwless terminal KF141R 4-way
Terminal for screwless clamping of wire from 26AWG to
18AWG.
- 4-fold
- type: KF141R (side insertion)
- pitch (distance between pins): 2.54mm
- strip the wire to 11mm In stock -
Magnet neodymium round 12mm x 5mm
Round neodymium magnet.
Diameter: 11.8mm
Height: 4.65mm
Warning: Neodymium magnets are not toys. Use them wisely!
Neodymium magnets are only shipped in a package due to possible disruption of postal sorting equipment.
In stock -
Magnet neodymium round 8mm x 5mm
Round neodymium magnet.
Diameter: 8mm
Height: 4.7mm
Warning: Neodymium magnets are not toys. Use them wisely!
Neodymium magnets are only shipped in a package due to possible disruption of postal sorting equipment.
In stock -
Magnet neodymium round 12mm x 3mm
Round neodymium magnet.
Diameter: 12mm
Height: 2.8mm
Warning: Neodymium magnets are not toys. Use them wisely!
Neodymium magnets are only shipped in a package due to possible disruption of postal sorting equipment.
In stock -
Magnet neodymium round 6mm x 3mm
Round neodymium magnet.
Diameter: 6mm
Height: 2.6mm
Warning: Neodymium magnets are not toys. Use them wisely!
Neodymium magnets are only shipped in a package due to possible disruption of postal sorting equipment.
In stock -
Neodymium magnet round 10mm x 2mm
Round neodymium magnet.
Diameter: 20mm
Height: 2mm
Warning: Neodymium magnets are not toys. Use them wisely!
Neodymium magnets are only shipped in a package due to possible disruption of postal sorting equipment.
In stock -
Magnet neodymium round 4mm x 2mm
Round neodymium magnet.
Diameter: 4mm
Height: 1.6mm
Warning: Neodymium magnets are not toys. Use them wisely!
Neodymium magnets are only shipped in a package due to possible disruption of postal sorting equipment.
In stock -
Magnet neodymium rectangular 20mm x 10mm x 2mm
Rectangular neodymium magnet.
Length: 19mm
Width: 9mm
Height: 1.8mm
Warning: Neodymium magnets are not toys. Use them wisely!
Neodymium magnets are only shipped in a package due to possible disruption of postal sorting equipment.
In stock -
Magnet neodymium rectangular 40mm x 20mm x 4mm N35
Rectangular neodymium magnet.
Length: 40mm
Width: 20mm
Height: 4mm
Magnetization: N35
Warning: Neodymium magnets are not toys. Use them wisely!
Neodymium magnets are only shipped in a package due to possible disruption of postal sorting equipment.
In stock -
BNC Cable male/male RG58 1 meter
Cable with 2 male BNC connections, for use with measuring equipment.
Length: ~1 meter In stock -
Electromagnetic lock 12V small - Lock plate
Lock plate for electromagnetic lock 12V small.
Dimensions: see image In stock -
USB Plug Type-A male to DIP adapter board
This adapter allows you to convert a male USB Type-A connector to a 2.54mm DIP format with 4 pins. Ideal for use in prototyping or integrating USB connectivity into custom circuits and breadboards.
Number of connections: 4
Grid: 2.54mm
PCB dimensions: 15.5mm x 15.5mm In stock -
USB Plug Type-A female to DIP adapter board
This adapter allows you to convert a USB Type-A female connector to a 2.54mm DIP format with 4 pins. Ideal for use in prototyping or integrating USB connectivity into custom circuits and breadboards.
Number of connections: 4
Grid: 2.54mm
PCB dimensions: 17mm x 17mm In stock -
Battery capacity meter/display for 3S lithium battery pack green
This capacity meter indicates the remaining capacity of a 3S lithium battery pack.
When the battery voltage is more than N*3.3V, 1 block of the display will light up.
When the battery voltage is more than N*3.5V, 2 blocks of the display will light up.
When the battery voltage is more than N*3.7V, 3 blocks of the display will light up.
When the bat... In stock -
ESP32-C3 Seeed Studio Xiao Development Board WiFi/Buetooth
Seeed Studio XIAO ESP32C3 is an IoT mini development board based on the Espressif ESP32-C3 WiFi/Bluetooth dual-mode chip. ESP32-C3 is a 32-bit RISC-V CPU, which includes an FPU (Floating Point Unit) for 32-bit single-precision arithmetic with powerful computing power. It has excellent radio frequency performance, supporting IEEE 802.11 b/g/n WiFi, ...
In stock
-
LED 5mm Multi-color/RGB Clear pre-wired for 5V-12V
Multi-color/RGB (slow flash) 5mm LED with clear lens and pre-wired with built-in resistor for use on 5V-12V.
Cable length: ~20cm In stock -
LED 5mm White Clear pre-wired for 5V-12V
White 5mm LED with clear lens and pre-wired with built-in resistor for use on 5V-12V.
Cable length: ~20cm In stock -
LED 5mm Red Clear Pre-wired for 5V-12V
Red 5mm LED with clear lens and pre-wired with built-in resistor for use on 5V-12V.
Cable length: ~20cm In stock -
LED 5mm Green Clear pre-wired for 5V-12V
Green 5mm LED with clear lens and pre-wired with built-in resistor for use on 5V-12V.
Cable length: ~20cm In stock -
LED 5mm Blue Clear pre-wired for 5V-12V
Blue 5mm LED with clear lens and pre-wired with built-in resistor for use on 5V-12V.
Cable length: ~20cm In stock -
Battery holder 18650 battery x 4
Battery holder with connection cables (150mm) that fit 4 batteries/rechargeable batteries of the type 18650.
Equipped with holes in the bottom so that the holder can be screwed onto a printed circuit board.
Dimensions: 76mm x 81mm x 20mm In stock -
Flat cable 20-pin rainbow 5 meters
5 meter ribbon cable in rainbow colours with 20 cores/poles for connecting PCBs etc. (Supplied without connectors).
Length: 5 meters
Spacing/grid: 2.54mm In stock -
Flat cable 10-pin rainbow 5 meters
5 meter ribbon cable in rainbow colours with 10 cores/poles for connecting PCBs etc. (Supplied without connectors).
Length: 5 meters
Spacing/grid: 2.54mm In stock -
Wire set 5 colors 1x0.50mm² 20AWG multi-core flexible
Wire set with wire in 5 different colours.
Colors: red, black, white, blue, yellow/green (2.5m per color)
The wire has a multi-stranded flexible core.
Rated voltage, UO / U: 450V/700V
Test voltage: 2500V
Conductor cross-section: 0.5 mm²
Temperature range:
- Fixed installation -40...+70°C
- When installing: +5...+70°C
Conductors 100% copper
-
Wire set 5 colors 1x0.75mm² 18AWG multi-core flexible
Wire set with wire in 5 different colours.
Colors: red, black, white, blue, yellow/green (2.5m per color)
The wire has a multi-stranded flexible core.
Rated voltage, UO / U: 450V/700V
Test voltage: 2500V
Conductor cross-section: 0.75 mm²
Temperature range:
- Fixed installation -40...+70°C
- When installing: +5...+70°C
Conductors 100% copper
-
Wire set 5 colors 1x1.50mm² 16AWG multi-core flexible
Wire set with wire in 5 different colors.
Colours: red, black, white, blue, yellow/green (2.5m per colour)
The wire has a multi-stranded flexible core.
Outer diameter: 3.64mm
Rated voltage, UO / U: 450V/700V
Test voltage: 2500V
Conductor cross-section: 1.5 mm²
Composition: 51x0.235mm
Minimum bending radius: 4 x diameter
Temperature range:
- Fixed... -
LED Tester
For quick testing of LEDs.
Supplied with 9V battery. In stock -
Infrared receiver LL-503PDD2E 940nm
Photo diode LL-503PDD2E from Lucky Light for receiving infrared signals.
Detection wavelengths: 700nm - 1200nm
Peak sensitivity at wavelength: 940nm
In stock -
Infrared receiver BPV10NF 940nm 40°
Photo diode BPV10NF from Vishay for receiving infrared signals at high frequencies and high data rates.
The Vishay BPV10NF is ideal for designing transmission systems according to IrDA requirements and for frequency-based carrier systems (e.g. ASK/FSK coded, 450 kHz or 1.3 MHz).
Detection wavelengths: 790nm - 1050nm
Peak sensitivity at wavelength... In stock -
LED board high power blue 5V 3W
Super bright blue LED on a driver board. Can be dimmed with a PWM signal on the S-connector. A PWM signal can be generated with an Arduino, Raspberry Pi or ESP8266/ESP32 for example.
You can also keep the LED on at 100% continuously by connecting S to the + terminal.
Current: 700mA
Connections:
+ - 5VDC
G - GND
S - high (5V) / low (GND) or PWM si... In stock -
LED board high power green 5V 3W
Super bright green LED on a driver board. Can be dimmed with a PWM signal on the S-connector. A PWM signal can be generated with an Arduino, Raspberry Pi or ESP8266/ESP32 for example.
You can also keep the LED on at 100% continuously by connecting S to the + terminal.
Current: 700mA
Connections:
+ - 5VDC
G - GND
S - high (5V) / low (GND) or PWM s... In stock -
LED board high power violet 5V 3W
Super bright violet/purple LED on a driver board. Can be dimmed with a PWM signal on the S-connector. A PWM signal can be generated with an Arduino, Raspberry Pi or ESP8266/ESP32 for example.
You can also keep the LED on at 100% continuously by connecting S to the + terminal.
Current: 700mA
Connections:
+ - 5VDC
G - GND
S - high (5V) / low (GND) ... In stock -
Digit display 4-digits 7-segments TM1637 clock green - 50x19mm
Green 4-digit clock display with TM1637 driver chip. The segments and numbers can be controlled separately.
Brightness can be adjusted by software.
The colon can be controlled, the individual points cannot.
Total board dimensions: 66x28x12mm.
Display dimensions: 50x19.5x7.8mm
Height of digits: 14mm (0.56inch)
Voltage: 5V
Interface:
GND - ground
... In stock -
Digit display 4-digits 7-segments TM1637 clock red - 50x19mm
Red 4-digit clock display with TM1637 driver chip. The segments and numbers can be controlled separately.
Brightness can be adjusted by software.
The colon can be controlled, the individual points cannot.
Total board dimensions: 66x28x12mm.
Display dimensions: 50x19.5x7.8mm
Height of digits: 14mm (0.56inch)
Voltage: 5V
Interface:
GND - ground
5V... In stock -
Digit display 4-digits 7-segments TM1637 clock blue - 50x19mm
Blue 4-digit clock display with TM1637 driver chip. The segments and numbers can be controlled separately.
Brightness can be adjusted by software.
The colon can be controlled, the individual points cannot.
Total board dimensions: 66x28x12mm.
Display dimensions: 50x19.5x7.8mm
Height of digits: 14mm (0.56inch)
Voltage: 5V
Interface:
GND - ground
5... In stock -
Digit display 4-digits 7-segments TM1637 clock yellow - 50x19mm
Yellow 4-digit clock display with TM1637 driver chip. The segments and numbers can be controlled separately.
Brightness can be adjusted by software.
The colon can be controlled, the individual points cannot.
Total board dimensions: 66x28x12mm.
Display dimensions: 50x19.5x7.8mm
Height of digits: 14mm (0.56inch)
Voltage: 5V
Interface:
GND - ground... In stock -
Number display 4-digits 7-segments TM1637 clock white - 50x19mm
White 4-digit clock display with TM1637 driver chip. The segments and numbers can be controlled separately.
Brightness can be adjusted by software.
The colon can be controlled, the individual points cannot.
Total board dimensions: 66x28x12mm.
Display dimensions: 50x19.5x7.8mm
Height of digits: 14mm (0.56inch)
Voltage: 5V
Interface:
GND - ground
... In stock -
Plastic Gear Set 11 Pieces
11-piece gear set with gears in various sizes.
For 2mm axles.
In stock -
Gear Plastic 120-tooth 0.5M for 2mm shaft
120-tooth plastic gear.
Modulus: 0.5M
Diameter: 61mm
Thickness: 4.3-7.4mm
Hole: 1.9mm (can be pressed onto a 2mm shaft)
Supplied individually. In stock -
Pulley plastic 17mm x 3.8mm x 1.9mm
Diameter: 17mm
Hole: 1.9mm (can be pressed onto a 2mm shaft)
Thickness: ~3.8mm In stock -
Signal connector JST XH 2.54mm 2-pole with wire and socket 15cm
Pin spacing: 2.5mm
Pins: 3
Wire thickness: 24AWG
Please note that the colours of the wiring may differ. Always check the correct connection. In stock -
Signal connector JST XH 2.54mm 3-pole with wire and socket 15cm
Pin spacing: 2.5mm
Pins: 3
Wire thickness: 24AWG
Please note that the colours of the wiring may differ. Always check the correct connection. In stock -
Signal connector JST XH 2.54mm 9-pin with wire and socket 15cm
Pin spacing: 2.5mm
Pins: 9
Wire thickness: 24AWG
(7-pin version shown).
Please note that the colours of the wiring may differ. Always check the correct connection. -
Signal connector JST XH 2.54mm 10-pin with wire and socket 15cm
Pin spacing: 2.5mm
Pins: 10
Wire thickness: 24AWG
(7-pin version shown).
Please note that the colours of the wiring may differ. Always check the correct connection. In stock -
Toggle switch with safety cap red
Illuminated rocker switch ASW-07D for switching DC voltage up to 12V.
Fire up your engines because these are the hot-rods of toggle switches! Equipped with an aerodynamic blue protective casing, and a diffused blue LED at the tip of the switch, this blue LED Toggle Switch is sure to add some flair (and flare!) to your project.
Often seen on contr... In stock -
Touch bed leveling sensor for 3D printers
3D Touch sensor for automatically leveling the print bed. With connection and mounting materials (some skill and familiarity with 3D printers is useful).
Working voltage: 5V
Current: 15mA (max. 300mA).
In stock -
Rubber string assortment 30-80mm (~30 pieces)
Assortment of approximately 30 pieces of rubber strings in sizes 30mm to 80mm for driving small models.
In stock -
Speaker 8 Ohm 1 Watt small rectangular 24x13x8mm
Small rectangular speaker for installation where space is limited.
With connection cable.
Features:
- Dimensions: 24mm x 13mm x 8mm
- Power: 1W
- Impedance: 8 Ohm In stock -
Audio decoder Stereo DAC I2S - UDA1334A
This UDA1334A I2S stereo DAC output is perfect for any audio interface with I2S output.
Logic levels from 3.3V-5V and can handle multiple different formats by setting two pins high or low.
The DAC processes the data instantly and produces a clear analog stereo line-level output.
Works with the Raspberry Pi and provides better sound quality than th... In stock -
MP3 player module with SD card and 3.5mm jack connection
Supports the following sample rates: 8KHz, 11.025KHz, 12KHz, 16KHz, 22.05KHz, 24KHz, 32KHz, 44.1KHz, 48KHz.
Fully supports FAT16/FAT32 file system, maximum support 16Gb.
With connection for 0-2W, 4-8Ω speakers.
Adjustable resistance for the volume.
With 9 pins to start 9 sound samples directly.
Pins:
- A1 - A9 - Trigger pins
- A10 - Stop playing
... In stock -
Bluetooth Audio module MH-MX8 M18
Simple bluetooth 4.2 audio module.
Once the module has been connected, a connection can be made to a telephone, for example, and audio can be played.
Connections: KEY, MUTE, VCC, GND, Audio L and Audio R.
The following buttons can be created on the KEY connection using resistors: Pause, Next/V+, Prev/V-, On/Off.
To do this, see the diagram in the... In stock -
Frame for Display LCD ST7920- 128x64 pixels
Frame for ST7920 128x64 pixel displays.
The display is screwed to the frame with the supplied screws.
Made of black ABS.
Dimensions: see pictures -
Weight sensor / Weighing cell / Load Cell 5kg
Weighing cell for weighing body weight up to 5kg.
By combining multiple cells (see the connection diagram) more weight can be weighed.
Watch a tutorial here: https://circuitjournal.com/50kg-load-cells-with-HX711
In stock -
Push button contact mini round yellow NC
Single pole push button that breaks contact as long as you keep it depressed (normally closed). When you release it, contact is restored.
Color: yellow
Diameter push button: 5.9mm
Diameter of drill hole: 6.6mm
Total length: 27.1mm (compressed 25.6mm) In stock -
Push button contact mini round red NC
Single pole push button that breaks contact as long as you keep it depressed (normally closed). When you release it, contact is restored.
Color: red
Diameter push button: 5.9mm
Diameter of drill hole: 6.6mm
Total length: 27.1mm (compressed 25.6mm) In stock -
Push button contact mini round white NC
Single pole push button that breaks contact as long as you keep it depressed (normally closed). When you release it, contact is restored.
Color: white
Diameter push button: 5.9mm
Diameter of drill hole: 6.6mm
Total length: 27.1mm (compressed 25.6mm) In stock -
Leadscrew / Spindle TR8x8 8mm 38cm
8mm Trapezium spindle, 8mm movement/revolution.
Mainly used on the Z axis of 3D printers.
Supplied without nut, see additional articles.
Diameter: 8mm
Length: 38cm
Lead: 8mm/rev.
Pitch: 2mm In stock -
Leadscrew / Spindle TR8x8 8mm 45cm
8mm Trapezium spindle, 8mm movement/revolution.
Mainly used on the Z axis of 3D printers.
Supplied without nut, see additional articles.
Diameter: 8mm
Length: 45cm
Lead: 8mm/rev.
Pitch: 2mm In stock -
Leadscrew / Spindle TR8x8 8mm 35cm
8mm Trapezium spindle, 8mm movement/revolution.
Mainly used on the Z axis of 3D printers.
Supplied without nut, see additional articles.
Diameter: 8mm
Length: 35cm
Lead: 8mm/rev.
Pitch: 2mm In stock -
Bed leveling spacer/distance bushing silicone 16mm orange (set of 4)
Set of 4 silicone spacers for leveling a heated print bed. Suitable for Creality 3D printers.
Inner diameter: 4-8mm
Outer diameter: 16mm
Height: 16mm
Colour: orange
-
Bed leveling spacer/distance bush silicone 16mm black (set of 4)
Set of 4 silicone spacers for leveling a heated print bed. Suitable for Creality 3D printers.
Inner diameter: 4-8mm
Outer diameter: 16mm
Height: 16mm
Colour black
-
Bed leveling spacer/distance bushing silicone 18mm orange (set of 4)
Set of 4 silicone spacers for leveling a heated print bed. Suitable for Creality 3D printers.
Inner diameter: 4-8mm
Outer diameter: 16mm
Height: 18mm
Colour: orange
-
Bed leveling spacer/distance bush silicone 18mm black (set of 4)
Set of 4 silicone spacers for leveling a heated print bed. Suitable for Creality 3D printers.
Inner diameter: 4-8mm
Outer diameter: 16mm
Height: 18mm
Colour black
-
Bed leveling screw set silicone 18mm M3 orange (set of 4)
Set of 4 silicone spacers with adjustment screw (M3) and adjustment knob for leveling a heated print bed. Suitable for Creality 3D printers.
Thread: M3
Inner diameter: 4-8mm
Outer diameter: 16mm
Height: 18mm
Colour: orange
In stock -
Bed leveling screw set silicone 18mm M4 orange (set of 4)
Set of 4 silicone spacers with adjustment screw (M4) and adjustment knob for leveling a heated print bed. Suitable for Creality 3D printers.
Thread: M4
Inner diameter: 4-8mm
Outer diameter: 16mm
Height: 18mm
Colour: orange
-
ESP32-S3 Espressif ESP32-S3-BOX-3
This fully open source AIoT development kit is based on the powerful ESP32-S3 AI SoC and is designed to revolutionize traditional development boards. We expect ESP32-S3-BOX-3 to be quickly developed as a next-generation development tool.
ESP32-S3-BOX-3 comes with a comprehensive range of add-ons, allowing developers to easily customize and extend ... -
Disassembly tools prying tools 3-piece
Tools for opening the casings of telephones and other electronics.
With these 3 metal tools you can easily pry open a housing without damaging it.
Lengths: 2x 17.5cm / 1x 16.5mm In stock -
Relay with USB control LCUS-1 (2-way)
USB board with two relays for switching a power supply up to a maximum of 10A (230VAC/30VDC).
With CH340 USB-to-serial chip (you can download drivers for this if your system does not recognize it yet).
After plugging in, a new COM or TTYS port will appear in your system.
By sending the following hex strings to it (connect at 9600 baud) you can swit... In stock -
Weight sensor / Weighing cell / Load cell 50kg
Weighing cell for weighing body weight up to 50kg.
By combining multiple cells (see the connection diagram) more weight can be weighed.
Watch a tutorial here: https://circuitjournal.com/50kg-load-cells-with-HX711
In stock -
Accelerometer 3-way digital - ADXL346 (GY-346)
The ADXL346 is a high resolution (13bit) 3-axis digital accelerometer.
The data can be read out through the digital SPI or I2C interfaces, making the ADXL346 sensor very suitable for use in Arduino projects.
It is suitable for both measuring static acceleration (such as tilt measurement) and measuring dynamic acceleration due to movements or shocks... -
Pluggable terminal 2-pin male - Dinkle 5EHDRC
In stock
-
Pluggable terminal 2-pin female - Dinkle 5ESDV
In stock
-
Connector MIDI DIN 5-pin chassis part female
5-pin female DIN chassis part for connecting MIDI equipment, among other things. To be soldered onto a printed circuit board yourself.
In stock
-
Connector MIDI DIN 5-pin female plug
5-pin female DIN connector for connecting MIDI equipment, among other things. Self-solderable.
In stock
-
Push button contact mini round blue NC
Single pole push button that breaks contact as long as you keep it depressed (normally closed). When you release it, contact is restored.
Color: Blue
Diameter push button: 5.9mm
Diameter of drill hole: 6.6mm
Total length: 27.1mm (compressed 25.6mm) In stock -
Push button contact mini round green NC
Single pole push button that breaks contact as long as you keep it depressed (normally closed). When you release it, contact is restored.
Color: green
Diameter push button: 5.9mm
Diameter of drill hole: 6.6mm
Total length: 27.1mm (compressed 25.6mm) In stock -
Grub screw M4x4mm
M4 x 4mm Allen key set screw.
Color: black
In stock -
Microswitch push button (make contact) 6x6x4.3mm vertical
Make contact micro switch push button for vertical mounting.
Dimensions (see also the images):
Width: 7.5mm
Height excl. pins: 7.2mm
Button length: 0.3mm (from housing)
Switching torque: 1.6N In stock -
Box header JST PH 4-pin male connector 2mm
Type: B4B-PH-KS
In stock
-
Capacitor 33µF 100V
In stock
-
LED 5mm Candle Effect Yellow Clear
5mm diameter LED with bright white lens. Provides yellow flickering 'candle light'.
Works on 2.5V-5V.
See the effect here: https://www.youtube.com/watch?v=uCgu-fQjHMg
In stock -
LED 5mm Candle Effect Yellow Rocket
5mm diameter LED with diffuse white 'rocket' lens. Gives yellow flickering 'candle light'.
Works on 2.5V-5V.
See the effect here: https://www.youtube.com/watch?v=OBqhb3UCF-Q
In stock -
LED 5mm Candle Effect Warm White Rocket
5mm diameter LED with diffuse white 'rocket' lens. Provides warm white flickering 'candle light'.
Works on 2.5V-5V.
See the effect here: https://www.youtube.com/watch?v=Rv9oVyrATBk
The actual color is slightly cooler than in the video.
In stock -
Humidifier / Mist maker ultrasonic miniature
Small humidifier for use in vivariums, miniatures, model building and Christmas houses (smoking chimney).
Place the 'wick' in the water, connect the 5V USB plug to the printed circuit board and as soon as the water has been sucked up, a fine stream of water vapour will come out of the humidifier.
The humidifier works ultrasonically, so no heat or h... In stock -
Relay with USB control LCUS-1 (single)
USB relay stick with a 1-channel relay for switching a power supply up to a maximum of 10A (230VAC/30VDC).
With CH340 USB-to-serial chip (you can download drivers for this if your system does not recognize it yet).
After plugging in, a new COM or TTYS port will appear in your system.
By sending the following hex strings to it (connect at 9600 baud)... In stock -
Linear bearing LMK8LUU
Linear bearing LMK8LUU with a diameter of 8mm for, among others. 3D printers.
Length: 45mm
Outer diameter: 15mm
Inner diameter: 8mm
Flange: 25mm x 25mm
Flange hole diameter: 4.7mm
Distance between holes: 16mm
In stock -
Motor DC 1.5V-6V 20mA 2000rpm
Type 300 DC motor, for small solar projects and repairs of miniatures such as Christmas houses.
With 7cm wire for connection.
Diameter: 24.5mm
Height incl. axle: 18.9mm
Diameter axle: 2mm
Voltage: 4.5V (works on 1.5V - 6V)
Current: 20mA
RPM: 2000
In stock -
Heart Rate Sensor / Pulse Oximeter MAX30102 I2C
The MAX30102 sensor is an integrated pulse oximetry sensor used to measure heart rate and blood oxygen saturation (SpO2) of a person or animal. This sensor was developed by Maxim Integrated and is widely used in wearables, medical devices, and other health monitoring applications.
The MAX30102 sensor can perform the following functions:
1. Heart ... In stock -
Air valve miniature 3VDC ⋄3mm
Small air valve with 3mm air hose connection.
The valve is normally open but closes when a voltage of 3VDC is applied.
Dimensions:
12.2mm x 10.2mm x 21.2mm (25.7mm incl. connection)
In stock -
Gas sensor set MQ sensors 9-piece
Set of 9 MQ gas sensors in a box consisting of the following sensors:
- MQ-2 LPG, (iso)butane, methane, alcohol, hydrogen gas, smoke
- MQ-3 alcohol, ethanol
- MQ-4 methane, natural gas
- MQ-5 LPG, isobutane, propane
- MQ-6 isobutane propane sensor
- MQ-7 CO/carbon monoxide
- MQ-8 hydrogen gas
- MQ-9 CO/carbon monoxide, flammable gas
- MQ-135 Air qu... In stock -
Power cord 230V flat euro plug 1.5m white
In stock
-
Power cord 230V flat euro plug 1.5m gray
In stock
-
Buck converter Step Up/Down DC-DC Uin:4.5V-28V Uout:0.8-20V MP1584EN
Super small buck step down converter.
Power supply module for energy-efficient reduction of a supply voltage.
The input voltage may be between 4.5 and 28 Volts.
The output voltage can be set from 0.8 to 20 Volts using the adjustable resistor.
Model: MP1584EN
Input voltage: 4.5V-28V
Output voltage (adjustable): 0.8-20V (output < input)
Output cur... In stock -
Relay - Solid state relay 3-32V / 40A / 24-380VAC Cover plate
Plastic cover plate for the solid state relay 3-32V / 40A / 24-380VAC.
In stock -
Heatsink E3D V6 remote/bowden zwart 1,75mm/3,0mm
E3D V6 Heatsink voor gebruik met bowden tube geschikt voor 1.75mm en 3,0mm filaments.
Je kunt in deze V6 heatsink een aparte heat break schroeven geschikt voor 1,75mm of 3,0mm filaments. In stock -
Heatsink E3D V5 remote/bowden aluminum 1.75mm
E3D V5 Heatsink for use with bowden tube suitable for 1.75mm filaments.
In stock
-
Stepper motor coupling semi-rigid 8x8mm
This semi-rigid stepper motor coupling connects an 8mm shaft to an 8mm shaft. Oa. for connecting stepper motors to a shaft.
Diameter: 20mm
Length: 25mm In stock -
Stepper motor coupling semi-rigid 5x8mm
This semi-rigid stepper motor coupling connects a 5mm shaft to an 8mm shaft. I.a. for connecting stepper motors to a shaft.
Diameter: 20mm
Length: 25mm In stock -
Audio amplifier LM386
This audio amplifier module is based on the LM386 chip. It has a gain (amplification value) of up to 200. The module includes speaker terminals, a power LED indicator and an adjustable 10K resistor, so you can adjust the gain volume.
Voltage: 5V ~ 12V
Dimensions: 41mm x13mm
Pinout:
- GND: Earth
- VCC: Supply voltage (5V~12V)
- IN: Audio signal
- ... In stock -
Audio amplifier 3W Class D I2S Breakout - MAX98357A
This compact audio amplifier 3W Class D I2S Breakout - MAX98357A delivers an impressive 3 Watt audio amplification with Class D amplification technology, ensuring clear and powerful sound.
One of the standout features of this product is the I2S interface, which provides a simple digital audio link to microcontrollers and other digital audio device... In stock -
Buck converter Step Up/Down DC-DC Uin:3.8-32V Uout:1.25V-35V 3A XL6009
Power supply module for energy-efficiently reducing and increasing a supply voltage.
The input voltage may be between 3.8 and 32 Volts.
The output voltage can be set to 1.25 to 35 Volts using the adjustable resistor.
Input voltage: 3.8-32V
Output voltage (adjustable): 1.25-35V
Output current: 3A
Conversion efficiency: 94% (max.)
Output ripple: 50... In stock -
Arduino Pro Mini Atmega328 5V 16MHz (open-source clone)
This Arduino Pro Mini (compatible clone) is intended for semi-permanent installation in objects or exhibitions, for example.
Its small dimensions make it easy to conceal in a housing.
Programming is done with the same software (Arduino IDE) as, for example, the Arduino Uno.
Specifications:
- Microcontroller: ATmega328PU
- Operating voltage: 3V
-... In stock -
DIY automatic irrigation kit
Set with all components to make your own automatic plant watering system.
The set contains the following parts:
- water pump
- water hose
- battery holder
- USB power cable
- soil moisture sensor
- comparator for setting the minimum humidity
- dupont cable
- relay for switching the pump
There is no manual included, but with the diagram on this si... In stock -
Microswitch keypad matrix 4x2
Simple 4x2 keypad with microswitches.
Pins K1 to K8 correspond to the push buttons. G is the common contact.
For direct connection to microcontrollers such as Arduino, Raspberry Pi, ESP8266 and ESP32 or with a multiplexer IC.
-
RFID/NFC PN532 Controller/Scanner Set
PN532 RFID/NFC controller/scanner set with controller board, key tag, key card, cable and header pins.
- Works with I2C/SPI and HSU (High Speed UART).
- Reads and writes with RFID
- P2P communication with peers
- NFC with Android
- NFC mode/RFID reader/writer mode
- On-board level shifter, Standard 5V TTL for I2C and UART, 3.3V TTL SPI
Reading di... In stock -
Motor DC 1.5V-6V 20mA 2000rpm with housing
Type 300 DC motor, for small solar projects.
With yellow housing and 13cm wire for connection.
Diameter incl. housing: 29mm
Height incl. housing and axle: 23.7mm
Diameter axle: 2mm
Voltage: 4.5V (works on 1.5V - 6V)
Current: 20mA
RPM: 2000
In stock -
Jumper cable male/female 4 pins 70cm
Jumper cable for use with 3D printers/repraps.
Pins: 4
Pin spacing/grid: 2.54mm
Length: 70cm
Cable colors: black/red/blue/green
In stock -
Freesset voor hout/metaal 6-delig
Set of 6 different HSS cutters for working with wood, metal and plastic with, among other things, a Dremel.
Dimensions: see pictures In stock -
Printed circuit board spacer self-adhesive 6.4mm/4mm Dremec
Spacer for mounting printed circuit boards in housings etc.
With self-adhesive bottom.
Distance bottom spacer to bottom 'peg': 6.4mm
Diameter peg/hole in printed circuit board: 4mm
Bottom dimensions: 17.8mm x 17.8mm
Thickness bottom: 1.6mm
Type: Dremec 8GB07V40993 In stock -
Optocoupler board PC817 2-channel
Optocoupler board with 2 optocouplers to keep the switching of e.g. relays optically separated from the rest of the circuit.
Voltage at the inputs for switching: 3.3V to 24V.
Voltage that can be connected to the outputs: 3.3V to 30V.
Dimensions: ~38mm x 29mm
In stock -
ESP32 WROOM Development board WiFi/Bluetooth Micro-USB with OLED display
ESP32 board with SSD1306 0.96 inch OLED display.
Most of the I/O pins are routed to pin headers (26 pins) on both sides for easy interfacing.
Developers can connect these pins to peripherals as needed. Standard headers also allow
development easy and convenient when using a breadboard.
The development board includes a mounted ESP-WROOM-32 module t... In stock -
Soldering practice set SMD hourglass
Set to practice soldering components.
This set has 1 SMD IC, the rest are THT components (including 57 LEDs).
With connection diagram.
Works on 4.5v.
Attention! Check the colors of the LEDs before soldering.
In stock -
Hotend CR10 kit with heater cartridge aluminum 1.75mm 12V/40W
Hotend kit for, among others, CR10 3D printers. For 1.75mm filament.
Supplied with 12V/40W heater cartridge, heat block, heat sink, 100K NTC thermistor, 2 pneufits, PTFE tube (1m) and 0.4mm MK8 nozzle.
In stock -
Power supply 12 Volt / 6A / 72W DC Meanwell LRS-75-12
Professional quality power supply from Meanwell. This is a 12 volt DC power supply with a power of 72W (6A).
This power supply is also suitable for LED installations.
- Type number: LRS-75-12
- Input Voltage: 88-264VAC, 50~60Hz
- Short circuit protection / overload protection
- Output voltage: 12V
- DC voltage adjustment: 10.8 - 13.8V
- Output cur... In stock -
Push button contact mini round black NO
Single-pole push button that makes contact as long as you keep it depressed (normally open). When you let go, the contact is broken.
Color: black
Diameter push button: 5.9mm
Diameter of drill hole: 6.6mm
Total length: 27.1mm (compressed 25.6mm) In stock -
ESP32 expansion board for 30-pin boards
This ESP32 expansion board is a versatile and useful tool designed for easy prototyping of projects.
It features header pins with power and ground rails, allowing for easy connections to various components.
Suitable for 30-pin ESP32 modules.
Power supply:
- 7-12V on DC connection.
- microUSB connector.
- USB C connector.
Specifications:
- Select... In stock -
Motion sensor/detector mmWave HLK-LD2410B (with BLE bluetooth)
The LD2410B is a highly sensitive 24GHz human presence status sensor developed by Hi-link. Its working principle is to use FMCW frequency modulated continuous wave to detect human targets in the set space. Combined with radar signal processing and precise human body detection algorithms, it realizes highly sensitive detection of human presence stat...
In stock
-
IC MCP3008 A/D converter 8-channel 10bit SPI
Need more analog inputs? This chip adds 8 10-bit channels to your microcontroller or microcomputer project. It is easy to use, communicates via SPI and therefore only requires 4 pins. This chip is a great addition to the Raspberry Pi computer, which does not have analog inputs itself.
Check out the website address for a library for the Arduino. In stock -
Pneufit with straight coupling JP4-01 M10 4mm
Pneufit straight coupling for connecting PTFE tube to extruders and hot ends.
Suitable for PTFE tube with a diameter of 4mm.
Thread: M10
Wire length: 6.15mm
Inner diameter: 4mm
Length: 17.7mm In stock -
Test clip set labclip to dupont female 10-piece
Test clip set with 10 lab clips to dupont female.
Handy for measuring circuits and flashing boards without soldering. For example in combination with a USB-to-serial adapter board.
Cable length: ~20cm In stock -
ESP32-CAM USB Programming/download board/shield
Use this board to program the ESP32 camera board through a USB connection.
You press the ESP32-CAM board on this (see image).
- With a push button on IO0 (to set the boot mode) and a reset button.
- Micro USB connection
- With CH340 USB serial chip.
(Delivered without the ESP32-CAM board). In stock -
Dupont connector kit 520 pieces
520-piece kit for making Dupont connectors yourself.
With male and female connectors, straight and angled header pins and 1.5m cable.
Pitch: 2.54mm
Connectors:
1X1P 40 pcs
1X2P 30 pcs
1X3P 20 pieces
1X4P 20 pcs
1X5P 20 pieces
1X6P 15 pcs
1X8P 15 pcs
1X10P 15 pieces
2X3P 5 pieces
2X4P 5 pieces
2X5P 5 pieces
2X6P 5 pieces
2X7P 5 pieces
2X8P 5 piec... In stock -
Motion sensor/detector Infrared PIR - SR602
Compact mini motion sensor based on an SR602 pyroelectric PIR sensor.
Operating voltage: 3.3-15VDC
Static power consumption: 20µA
Output: high (3.3V) - low (0V)
Delay time: ~2.5 seconds (changeable by changing a resistor).
Block time: 2 seconds
Lens dimensions: 10x10mm
An F3 photodiode can be connected to the S- and S+ connections.
In stock -
Temperature sensor I2C Contactless GY-906-BAA
The GY-906 BAA is a temperature sensor, based on an integrated 3V single zone infrared thermometer. The sensor measures without touching the surface to be measured.
- Mounted on a starter plate with two types of pins.
- 10k pull-up resistors for I2C interface with optional solder bridges.
- Easy to integrate.
- Factory calibrated over a wide tempe... In stock -
Temperature sensor and humidity sensor DHT11 on breakout - KY-015
The DHT11 is a temperature and humidity sensor in 1.
Because the DHT11 provides a digital output, it is perfect for all kinds of Arduino projects!
For example, starting a fan if a room becomes too humid or too warm.
(Google DHT11 Arduino for programming examples and libraries.)
This version already comes on a handy break-out board.
Response time: ... In stock -
LED 10mm RGB Module 5V - 140C05
Handy LED module with 3 LEDs in green, red and blue. The LEDs can be controlled individually with 5V via their own pins. This allows you to connect them directly to an Arduino, for example (see connection diagram).
Put 5V on the V-pin and connect the RGB pins to a digital output of the Arduino. By making the pins low (0V) the LED will light up.
If ... In stock -
Motion sensor/detector Infrared PIR - AM312
Compact mini motion sensor based on an AM312 pyroelectric PIR sensor.
Operating voltage: 2.7-12VDC
Static power consumption: In stock -
Solar LiPo Charger CN3065
This is a mini Solar Lipo charger based on the CN3065 - a single lithium battery charge management chip.
This solar charger gives you the opportunity to get the most possible current from your solar panel or other photovoltaic device and put it into a rechargeable LiPo battery.
Installation is simple: simply connect your solar panel to one side of... In stock -
Silicone wire set multi-core 10AWG 1 meter - red + black
Extra flexible silicone wire that can withstand temperatures up to 200°C and voltages up to 600V.
1 meter red + 1 meter black. -
ESP32-C3 Super Mini Development Board WiFi/Buetooth
A super small mini ESP32-C3 board for compact projects.
- The ESP32C3 SuperMini is an IoT mini development board based on the Espressif ESP32C3 WiFi/Bluetooth dual-mode chip. ESP32-C3 is a 32-bit RISC-V CPU with a floating point unit (FPU), which can perform 32-bit single-precision operations and has powerful computing power.
- The board has excel... In stock -
ESP32-S3 DevKitC N16R8 Development Board WiFi/Buetooth
Powerful full-size ESP32-S3 board with 16MB external flash, 8MB PSRAM 384K ROM and 512K onboard SRAM.
- With WiFi and (BLE) Bluetooth
- Equipped with 2 type-C USB ports (CH343P serial + OTG).
- Most of the I/O pins on the module are broken out into the pin headers on both sides of this board, making them easy to connect.
- Reset button
- Boot butt... In stock -
Solar Power Management Module Waveshare
This solar power management module is designed for 6V~24V solar panel. It can charge 3.7V rechargeable Li-battery via solar panel or USB port, and provides 5V/1A or 3.3V/1A regulated output. You can easily connect MCU such as Arduino or ESP to it.
The module has the MPPT (Maximum Power Point Tracking) function and multiple protection circuits, whi... In stock -
Arduino UNO R4 WiFi, RA4M1, ESP32-S3
The Arduino UNO Rev4 WiFi combines the processing power and exciting new peripherals of Renesas RA4M1 microcontroller (R7FA4M1AB3CFM#AA0) with the wireless connectivity power of Espressif's ESP32-S3.
The memory of the UNO R4 WiFi is larger than its predecessors,
with 256 KB flash, 32 KB SRAM and 8 KB EEPROM.
Furthermore, the UNO R4 WiFi offers a bu... In stock -
Arduino UNO R4 Minima, R7FA4M1AB3CFM
Upgraded and improved; the Arduino UNO Rev4 Minima is equipped with a powerful RA4M1 32-bit microcontroller from Renesas (R7FA4M1AB3CFM#AA0, a 48 MHz Arm® Cortex®-M4 microprocessor. The memory of the UNO R4 is larger than that of its predecessors
256 KB flash, 32 KB SRAM and 8 KB data memory (EEPROM).
Brace yourself for more processing power, ex... In stock -
Microswitch push button (make contact) mouse 6x6x7.3mm Kailh
Make contact micro switch push button. This switch is often used in mice as the click contact of the mouse wheel and side buttons.
Width: 6mm
Length: 6mm
Button height: 1mm (from top of housing)
Total height: 7.3mm In stock -
IC NTE4006B Static Shift Register
The NTE4006B is a static shift register IC (Integrated Circuit) used to convert parallel data to serial output. The IC has six independent shift registers, each with a capacity of 4-bits. It is ideal for applications that require data sequencing and storage, such as serial communications, data acquisition, and LED display control.
-
IC ULN2803A Darlington Array
The ULN2803A is a high-performance IC (integrated circuit) used to switch and control higher current loads using a microcontroller or other logic circuits.
This IC contains eight Darlington transistors with built-in diodes that eliminate inductive effects. This makes the ULN2803A ideal for driving relays, stepper motors, LED displays and other indu... In stock -
LED Board SparkFun Qwiic LED Stick - APA102C - COM-18354
The SparkFun Qwiic LED Stick features ten addressable APA102 LEDs, making it easy to add full color LED control using I2C. Write to individual LEDs to display a binary count, or write to the entire strip for cool lighting effects. You can even add more LEDs to the end if needed. We've written an Arduino library and Python package that handle the I2...
Adafruit Part number: 474-COM-18354
-
Soldering set 60W 4-piece
4-piece 50W soldering set consisting of:
Soldering iron 60W
- Soldering iron with rubber grip for a good grip. With long-life tip.
Desoldering pump / Tin sucker
- With a desoldering pump you can quickly and easily suck liquid tin away from your circuit, allowing you to remove components and wiring. A handy tool that always comes in handy when sol... In stock -
USB Connector USB Type-C
Self-soldered USB Type C connector. With connections for 5V, GND and 2 data lines.
The housing must be glued with superglue or hot glue. In stock -
USB Connection Cable USB A <-> USB C 1.0 meter white
You use this cable to connect devices with a USB-C connection, such as a Raspberry Pi or ESP32, to a computer.
Length: 1.0m
Color: white
Technical specifications:
Type: Charging/Data Cable
Connections: USB-A to USB-C
Supported: QC up to 18W (9V/2A)
Bandwidth: up to 480 Mbit/s
Standard: 2.0 Compatible: with all USB-A interfaces (including Hi-Speed... In stock -
USB Connection Cable USB A <-> USB C 0.5 meter white
You use this cable to connect devices with a USB-C connection, such as a Raspberry Pi or ESP32, to a computer.
Length: 0.5m
Color: white
Technical specifications:
Type: Charging/Data Cable
Connections: USB-A to USB-C
Supported: QC up to 18W (9V/2A)
Bandwidth: up to 480 Mbit/s
Standard: 2.0 Compatible: with all USB-A interfaces (including Hi-Speed... In stock -
Combination side cutting pliers cutting/stripping 140mm
This combination side cutting pliers enables precise cutting and stripping with just one tool. The carbon steel used for the slightly curved cutting edge offers high hardness combined with long life and sufficient sharpness for both small and large wire diameters.
A high-frequency heat-treated sharp blade is used for stripping, which can process d... In stock -
M5Stack ATOM Echo Smart Speaker Development Kit - ESP-PICO-D4
ATOM ECHO is a programmable smart speaker based on the M5ATOM design. The form factor is very small, the dimensions are only 24x24x17mm.
Music can be played using the ESP32's Bluetooth capabilities from a mobile phone or tablet.
The device can be programmed to access AWS, Baidu and other cloud platforms, using the built-in microphone and speake... Adafruit Part number: 170-C008-C -
Motor speed controller DC 10V-60V 20A (PWM)
PWM speed controller for DC motors with a voltage of 10V to 60V. The speed can be regulated linearly between 0 and 100% using the rotary knob.
Simply connect the plus and minus of the power supply and the plus and minus of the motor.
Supply voltage: 10-60VDC
Frequency: 25kHz
Maximum power: 1200W (peak)
Continuous current: 18A
Maximum current: 20A
... In stock -
Cooling block for TEC1 Peltier cooling element
Aluminum cooling block for water cooling of TEC1 peltier cooling elements.
Dimensions:
Block: 40.5mm x 57.2mm x 12.0mm
Hose connections: 6mm internal / 9mm external
In stock -
Bowden tube buckle/clip 6mm
Buckle/clamp/clip for securing the PTFE tube to, among other things. the extruder.
I.a. for the Ultimaker 2.
Dimensions:
Inner diameter: 6.6mm
Outer diameter: 7.8mm
Height: 8.45mm In stock -
Pneufit with straight coupling PC4-01 for, among others, E3D-V6
Pneufit straight coupling for connecting PTFE tube to extruders and hot ends.
Suitable for PTFE tube with a diameter of 4mm.
Thread: M10
Wire length: 6.3mm
Inner diameter: 4mm
Outer diameter (thread): 9.5mm
Length: 18.9mm In stock -
Carbon film resistor set 5% 560 pieces
Set of 560 pieces carbon film resistors.
Features:
Applications: TV, audio and video equipment, telephone receivers and communication systems, instrumentation, household appliances, etc.
Specifications:
Quantity: 560 pcs. (10 pcs. per value)
Number of values: 50 (from 1 to 10M)
Nominal power: 1/4W
Working temperature: -55°C to 155°C
Tolerance... In stock -
Optocoupler board PC817 8-channel
Optocoupler board with 8 optocouplers to keep the switching of e.g. relays optically separated from the rest of the circuit.
Voltage at the inputs for switching: 3.3V to 24V.
Voltage that can be connected to the outputs: 3.3V to 30V.
Dimensions: ~47.3mm x 37.7mm
In stock -
Stand/Holder for 16x2 1602 LCD display modules - clear acrylic
This is a LCD screen 16x2 LCD1602 holder made of clear acrylic. This transparent acrylic case is strong and handy.
This stylish holder will definitely give your project an aesthetic boost.
Supplied without display. In stock -
Automatic temperature controller W3230 with display 24VDC (relay)
Automatic W3230 built-in temperature controller with a 24 volt DC power supply.
The display shows the current (PV) and set (SV) temperature values. The OUT light indicates whether the relay is switched on.
Temperature range: -50°C - 120°C
Resolution: 0.1°C (at -9.9°C - 99.9°C) - 1°C (at other values).
Accuracy: 0.1°C
Hysteresis accuracy: ... In stock -
Automatic temperature controller W3230 with display 230VAC (relay)
Automatic W3230 built-in temperature controller with a 230V AC power supply.
The display shows the current (PV) and set (SV) temperature values. The OUT light indicates whether the relay is switched on.
Temperature range: -50°C - 120°C
Resolution: 0.1°C (at -9.9°C - 99.9°C) - 1°C (at other values).
Accuracy: 0.1°C
Hysteresis accuracy: 0.1... In stock -
Automatic temperature controller W3230 with display 12VDC (relay)
Automatic W3230 built-in temperature controller with a 12 volt DC power supply.
The display shows the current (PV) and set (SV) temperature values. The OUT light indicates whether the relay is switched on.
Temperature range: -50°C - 120°C
Resolution: 0.1°C (at -9.9°C - 99.9°C) - 1°C (at other values).
Accuracy: 0.1°C
Hysteresis accuracy: ... -
Battery capacity meter/display for lithium batteries blue
This capacity meter indicates the remaining capacity of a lithium battery or lithium battery.
Input voltage: 6V- 72V
Dimensions: 61.3mm x 33.3mm x 13.5mm
Display color: blue In stock -
Battery capacity meter/display for lithium batteries green
This capacity meter indicates the remaining capacity of a lithium battery or lithium battery.
Input voltage: 6V- 72V
Dimensions: 61.3mm x 33.3mm x 13.5mm
Display color: green
To enter the settings: hold the left set button while connecting the power. In stock -
Battery capacity meter/display for lithium batteries white
This capacity meter indicates the remaining capacity of a lithium battery or lithium battery.
Input voltage: 6V- 72V
Dimensions: 61.3mm x 33.3mm x 13.5mm
Display color: white In stock -
Micro switch push button (make contact) 12x12mm with LED white
Microswitch push button with white LED.
Diameter button: 6.9mm
Case Dimensions: 12mm x 12mm x 7.3mm
Other dimensions: see images.
Voltage LED: 3.5V max.
Switches max. 12V / 0.5A
In stock -
Micro switch push button (make contact) 12x12mm with red LED
Microswitch push button with red LED.
Diameter button: 6.9mm
Case Dimensions: 12mm x 12mm x 7.3mm
Other dimensions: see images.
Voltage LED: 3.5V max.
Switches max. 12V / 0.5A
In stock -
Micro switch push button (make contact) 12x12mm with green LED
Microswitch push button with green LED.
Diameter button: 6.9mm
Case Dimensions: 12mm x 12mm x 7.3mm
Other dimensions: see images.
Voltage LED: 3.5V max.
Switches max. 12V / 0.5A
In stock -
Micro switch push button (make contact) 12x12mm with LED yellow
Microswitch push button with yellow LED.
Button diameter: 6.9mm
Case Dimensions: 12mm x 12mm x 7.3mm
Other dimensions: see images.
Voltage LED: 3.5V max.
Switches max. 12V / 0.5A
In stock -
Micro switch push button (make contact) 12x12mm with LED blue
Microswitch push button with blue LED.
Diameter button: 6.9mm
Case Dimensions: 12mm x 12mm x 7.3mm
Other dimensions: see images.
Voltage LED: 3.5V max.
Switches max. 12V / 0.5A
In stock -
LilyGO TTGO T4 ESP32 + 2.4inch ILI9341 LCD display
LiliyGO TTG0 T4 ESP32 WiFi development board with onboard 2.4inch ILI9341 TFT LCD display.
- Processor: ESP32
- Connectivity: WiFi 802.11b/g/n, BL V4.2 + BLE bluetooth
- Programming platforms: Arduino IDE, MicroPython
- Serial chip: CH9102
- Flash: 4MB
- PSRAM: 8MB
- Battery voltage detection
- Function buttons: boot + reset
65K Color display:
- ... In stock -
LilyGO TTGO T5 V2.3.1 ESP32 + 2.13inch DEPG0213BN E-paper display
LilyGO TTGO T5 ESP32 WiFi development board with onboard 2.13inch DEPG0213BN E-paper display.
- Processor: ESP32
E-Paper display:
- DEPG0213BN4 driver
- Resolution: 212(H) x 104(V)
- Grey levels: 2
- Power: 3.3V
Dimensions:
- 36.75mm x 66.3mm x ~10mm
Even after the power is turned off, the contents of the E-paper screen remain visible.
Version ... In stock -
LILYGO T-Display-S3 ESP32-S3 + 1.9inch ST7789 LCD display
LiliyGO T-Display-S3 ESP32 WiFi development board with onboard 1.9 inch ST7789 display.
- Processor: ESP32-S3R8 dual core LX7
- Connectivity: WiFi 802.11, BLE 5 + BT mesh bluetooth
- Programming platforms: Arduino IDE, MicroPython
- Flash: 16MB
- PSRAM: 8MB
- Battery voltage detection on IO04
- Function buttons: boot + reset + IO14 button
Full co... In stock -
ESP32 WROOM Development board WiFi/Bluetooth USB-C CH340
Most of the I/O pins are routed to pin headers (30 pins) on both sides for easy interfacing.
Developers can connect these pins to peripherals as needed. Standard headers also allow
development easy and convenient when using a breadboard.
The development board includes a mounted ESP-WROOM-32 module that combines Wi-Fi, Bluetooth and Bluetooth LE fo... In stock -
Adjustable soldering station ceramic 48W 150°C - 420°C - Velleman VTSSC50
Specifications:
- manual temperature control
- power-on indication via LED
- with on/off switch
- ceramic heating element (48W)
- with holder for left or right handed use
- standard soldering tip (incl.): BITC50N2
Electrical data:
- Protection by fuse
Technical data:
- Fast heating
- ESD protection
Features:
- Standby mode
- Adjustable temperatu... -
Housing Universal ABS (splash) waterproof 200x120x56mm
For housing your project in a humid environment.
Not for underwater!
Dimensions: 200mm x 120mm x 56mm
Internal dimensions: 194x109x50mm
Color: gray -
Self-adhesive Velcro pads 10mm - 200 pieces
These Velcro pads are the ideal helpers to attach certain items in a stable or non-slip manner and to leave the option open to loosen these items occasionally if necessary and then reattach them later.
Set consisting of 200 self-adhesive Velcro pads (each hook pad/fleece pad) of 10mm.
Material: nylon/polyester with a maximum of 10,000 closing/ope... In stock -
Ruler set stainless steel 3-piece 15/20/30cm
Whether for professional use, DIY, office or school, with this stainless steel ruler set you have 3 durable, neat rulers for many applications.
The rulers have lengths of 15, 20 and 30 cm and are clearly and accurately marked with a centimeter scale and an inch scale on the back.
Material thickness is 0.8 mm (30 cm), 0.6 mm (20 cm) or 0.5 mm (15 ... In stock -
BNC Plug with male terminal block
BNC male plug with terminal block/screw connection for easy connection of wires without soldering.
In stock
-
BNC plug with terminal block female
BNC female plug with terminal block/screw connection for easy connection of wires without soldering.
In stock
-
LED Ring 3x WS2812 RGB 5050 RGB LEDs with drivers (3bits)
Ring with 3 WS2812 5050 RGB LEDs.
The LEDs can be controlled individually (on/off, color and brightness) with only 2 wires from e.g. an Arduino.
Diameter: 22.7mm
See:
https://github.com/FastLED/FastLED
For connection see:
https://www.tweaking4all.nl/hardware/arduino/arduino-ws2812-led// In stock -
LED Board 1x WS2812B 5050 RGB LED with driver (1bit)
LED board with 1 individually controllable WS2812B RGB LED.
The LED is easily controlled from an Arduino with a single signal pin, for example with the FastLED library. (See website link.) Connect the signal pin of the Arduino to the IN pin of the board.
The boards can be interconnected by connecting the IN and OUT pins.
Supply voltage: 5V
For ... In stock -
External shunt resistor FL-2 0.5% - 100A 75mv
External shunt resistor for measuring high current up to 100A.
In stock -
LilyPad battery holder for CR2032 battery
Holder for CR2032 batteries for use with LilyPad components.
In stock -
INMP441 MEMS I2S Microphone module
INMP441 is a high-quality, low-power, digital, omnidirectional MEMS microphone. This microphone can be connected directly to an ESP32 microcontroller to create a voice assistant, for example.
The complete INMP441 solution consists of a MEMS sensor, signal composition conditionin, analog-to-digital converter, anti-aliasing filter, power management ... In stock -
Ball bearing 626ZZ 19x6x6mm
Double shielded ball bearing 626ZZ.
Outer diameter: 19mm
Inner diameter: 6mm
Thickness: 6mm In stock -
Ball bearing 6200Z 30x10x9mm
Dimensions:
Outside size: 30m
Inner size: 10mm
Height: 9mm
-
Ball bearing 6001Z 28x12x8mm
Dimensions:
Outside size: 28m
Inner size: 12mm
Height: 8mm In stock -
Cinch chassis part stereo red/white
Tulip chassis (red/white) angled for printed circuit board mounting.
Dimensions: 30mm x 18mm x 19mm In stock -
Jumper cable male/female 2 pins 50cm
Jumper cable male/female for use with 3D printers/repraps.
Pins: 2
Pin spacing/grid: 2.54mm
Length: 50cm
Cable colours: black/red In stock -
Loudspeaker Chassis / Terminal square 56x56mm
Loudspeaker connection chassis part square 56x56mm black with black and red clamp connection.
Suitable for wires up to ⋄3.5mm
Dimensions: 56mm x 56mm x31mm
Terminals: 4.2mm In stock -
Speaker Chassis / Terminal round 65mm
Loudspeaker connection chassis part round 65mm black with black and red clamp connection.
Suitable for wires up to ⋄3.5mm
Dimensions: ⋄65mm x 31mm
Terminals: 4.5mm In stock -
RFID Tag / Keychain 13.56MHz red
ISO/IEC 14443 RFID 13.56MHz Tag / key fob with unique code.
These RFID 'droplets' can be applied in various RFID projects.
Frequency: 13.56MHz
Reading/writing distance: 2.5 ~ 10cm
Read/Write Time: 1~2ms
Dimensions: 30mm x 40mm x 3mm
Color: red
In stock -
Resin filter / Paint filter paper (10 pieces)
Filters for filtering resin or paint. Filtering the resin left in the container ensures that there are no (hard) residues left that could ruin your next print.
The filters can be thrown away after use.
Set of 10 filters.
Material: paper / nylon
Dimensions: ⌀15cm x 10cm In stock -
Resin filter / sieve 2-piece
Handy 2-piece filter for filtering resin / printing resin. The set consists of a metal sieve and a matching silicone funnel.
Filtering the resin ensures that any remaining hard pieces do not end up in the next print.
Sieve diameter: ~64mm
Sieve height: 29mm In stock -
LED 5mm Orange
Orange 5mm LED with orange lens. In stock
-
Servo motor digital MG946R high torque metal gears
Operating speed: 0.20sec / 60 degrees (4.8V no load)
Operating speed: 0.17sec / 60 degrees (6.0V no load)
Stall torque: 10.5 kg-cm @ 4.8 V
Stall torque: 13 kg-cm @ 6 V
Operating voltage: 4.8-7.2 volts
Gear Type: All Metal Gears In stock -
Servo motor digital MG945 high torque metal gears
Operating speed: 0.17sec / 60 degrees (4.8V no load)
Operating speed: 0.13sec / 60 degrees (6.0V no load)
Stall torque: 13 kg-cm @ 4.8 V
Stall torque: 15 kg-cm @ 6 V
Operating voltage: 4.8-7.2 volts
Gear Type: All Metal Gears In stock -
Servo motor digital MG995 high torque metal gears
Operating Speed: 0.17sec / 60 degrees (4.8V no load)
Operating Speed: 0.13sec / 60 degrees (6.0V no load)
Stall Torque: 13 kg-cm @ 4.8V
Stall Torque : 15 kg-cm @ 6V
Operation Voltage: 4.8 - 7.2 Volts
Gear Type: All Metal Gears
In stock -
Distance Sensor Ultrasonic Splashproof JSN-SR04T Onboard
An ultrasonic distance sensor similar to the HC-SR04 but splashproof. With the sensor on-board.
- Voltage: 5VDC
- Current:20mA
- Frequency: 40KHz
- Range: 30cm - 3.5m
- Resolution:1cm
- Output signal: 5V
- Angle: < 80° In stock -
Relay board 16-channel 5V - optocoupled
Easily control 16 relays from a microcontroller (Arduino) with 5V.
With LEDs indicating the status of the relays.
Equipped with optocouplers, which electrically separate your microcontroller from the relay.
With convenient screw terminals for connecting the device to be switched.
Each relay has a normally open and a normally closed contact.
A jumpe... In stock -
LED Matrix Display Module 8x8 4-way MAX7219 Green
LED matrix display module with 4 pieces 8x8 green LEDs controlled by a MAX7219.
Using 3 inputs from your Arduino or other MCU you can control all LEDs individually.
For example, use the LCDemoCascadedDevices sketch from the LEDcontrol library (see the website link below).
For a connection example, see the programming examples.
Supplied with 5 pin... In stock -
LED Matrix Display Module 8x8 4-way MAX7219 Blue
LED matrix display module with 4 pieces 8x8 blue LEDs controlled by a MAX7219.
Using 3 inputs from your Arduino or other MCU you can control all LEDs individually.
For example, use the LCDemoCascadedDevices sketch from the LEDcontrol library (see the website link below).
For a connection example, see the programming examples.
Supplied with 5 pin ... In stock -
Peltier cooling element insulation foam
Foam for insulating Peltier cooling element TEC1 12706 TEC.
Dimensions: 40mm x 40mm x 3.8mm In stock -
Brush with brass bristles
Brush with brass bristles, including for cleaning nozzles of 3D printers.
Brush length: 15cm
Brush head dimensions: 33x9mm
Bristle length: 13mm In stock -
Wire for connecting RGB LEDs 0.35mm² 22AWG per meter
Wire with the colours red, green, blue and black for connecting, among other things, RGB LEDs.
Length: 1 meter (multiple pieces delivered as one piece)
Thickness: 22AWG / 0.35mm2
In stock -
Dosing pump/Water pump peristaltic 6V silicone/silent
Silent pump for dosing liquids. The liquid is pumped through the hose by the rotating movement of the 6V motor. The liquid does not come into contact with the motor because the liquid remains in the hose.
Ideal for dosing nutrients or chemicals in an aquarium.
Power supply: 6V DC
Current: 100mA
Current direction: depends on how the plus and minus ... -
Electronic components starter kit large E23
Various types of electronic components in a handy storage box.
Great to start with or to supplement your existing component stock.
- 10 pieces 5mm LEDs white
- 10 pieces 5mm LEDs yellow
- 10 pieces 5mm LEDs blue
- 10 pieces 5mm LEDs green
- 10 pieces 5mm LEDs red
- 1 pc 5mm LED RGB
- 2 pieces 40 pin header pins
- 1 piece Breadboard power module ... In stock -
Heat break MK10 M7 26x7.8mm 1.75mm
Heatbreak voor Creality CR10 all-metal voor 1,75mm filament.
Lengte: 26mm
Diameter: 7,8mm
Schroefdraad: M7
Lengte schroefdraad: 4mm
Binnendiameter: 4,1mm / 2mm
In stock -
Heat break CR10 M6 23x7mm 3mm all-metal
Heatbreak for Creality CR10 all-metal for 3mm filament.
Length: 23mm
Diameter: 7mm
Thread: M6
Thread length: 6mm
Inner diameter: 4mm / 3mm
In stock -
Heat break CR10 M6 23x7mm 4.1mm all-metal
Heatbreak for Creality CR10 all-metal for 4mm tube.
Length: 23mm
Diameter: 7mm
Thread: M6
Thread length: 6mm
Inner diameter: 4.1mm
In stock -
Heat break CR10 M6 23x7mm 1.75mm with Teflon
Heatbreak for Creality CR10 with Teflon lining for 1.75mm filament.
Length: 23mm
Diameter: 7mm
Thread: M6
Thread length: 6mm
Inner diameter: 4mm / 3mm
In stock -
Heat break CR10S 27x7x4mm
Heat break for, among others. Creality CR-10, CR-10S, S4, S5, Ender 3 / Pro Series.
Length: 27mm
Diameter: 7mm
Inner diameter: 4mm
Thread diameter: M6
Thread length: 5mm
In stock -
Raspberry Pi 3/4 RGB Fan kit with OLED display
- Real-time OLED screen status display: The OLED screen can display the actual CPU temperature, CPU usage, hard disk space, memory and IP address.
- Programmable RGB LEDs: 3 programmable high-brightness RGB LEDs onboard, which can provide multiple lighting mode commands through programming. You can even use the RGB light color to indicate the moth... In stock -
CC Debugger USB dongle for CC2531/CC2540
CC Debugger USB dongle for programming/flashing CC2531/CC2540 ZigBee sticks.
-
Bed leveling spring for 3D printers 8mm x 5mm
Replacement spring for leveling the heated bed.
Length: 8mm
Diameter: 5mm In stock -
Raspberry Pi Pico - RP2040 - Cortex-M0+ - MicroUSB with header pins
At the heart of the Raspberry Pi Pico microcontroller board is a custom Raspberry Pi-designed chip called the RP2040 featuring a 133MHz clocked ARM Cortex-M0+ dual-core with integrated 2MB QSPI flash memory for code and data storage.
You can program your Pico by simply connecting it to a computer/notebook via USB and then transferring a previously... In stock -
Raspberry Pi Pico - RP2040 - Cortex-M0+ - MicroUSB
At the heart of the Raspberry Pi Pico microcontroller board is a custom Raspberry Pi-designed chip called the RP2040 featuring a 133MHz clocked ARM Cortex-M0+ dual-core with integrated 2MB QSPI flash memory for code and data storage.
You can program your Pico by simply connecting it to a computer/notebook via USB and then transferring a previously... In stock -
Pneufit with straight coupling PC6-01
Pneufit straight coupling for connecting PTFE tube to extruders and hot ends.
Suitable for PTFE tube with a diameter of 6mm for 3mm filament.
Inner diameter: 6.3mm
Wire length: 6.6mm
Length: 19.5mm In stock -
Bed adjustment screw for 3D printers
Adjusting screw for adjusting the heated bed of a 3D printer.
Bolt length: 42.8mm
Nut diameter: 13.8mm In stock -
V-Slot Openbuilds Gantry Plate kit 2040
Complete 2040 gantry plate kit with 4 V-slot wheels.
Plate dimensions: 50mm x 50mm
Other dimensions: see images
In stock -
V-Slot Openbuilds Gantry Plate kit 2020
Complete 2020 gantry plate kit with 4 V-slot wheels.
Plate dimensions: 65.5mm x 65.5mm
Other dimensions: see images
In stock -
Linear bearing LMK10LUU
Linear bearing LMK10LUU with a diameter of 10mm for, among others. 3D printers.
Length: 55mm
Outer diameter: 19mm
Inner diameter: 10mm
Flange: 30.8mm x 30.8mm
Flange hole diameter: 4.7mm
Distance between holes: 21.5mm
Image differs (length). In stock -
Linear bearing LMK12LUU
Linear bearing LMK12LUU with a diameter of 12mm for, among others. 3D printers.
Length: 57mm
Outer diameter: 21mm
Inner diameter: 12mm
Flange: 32.4mm x 32.4mm
Flange hole diameter: 4.7mm
Distance between holes: 22.8mm
Image differs (length). In stock -
Wheel for 2mm axle 30mm yellow
Diameter: 30mm
Width: 13mm
Axle: 2mm In stock -
Pulley plastic 20mm x 4mm x 1.9mm
Diameter: 20mm
Hole: 1.9mm (can be pressed onto a 2mm shaft)
Thickness: 4mm In stock -
Gear Metal 12-tooth
12-tooth metal gear.
Diameter: 8.4mm
Thickness: 7.5mm
Hole: 3mm
See images for all dimensions.
Supplied individually. -
Plastic Gear Set 15 Pieces
15-piece gear set with gears in various sizes.
See images for axle sizes and diameters.
In stock -
Worm wheel Plastic 10mm x 6mm x 2mm
Length: 10mm
Diameter: 6mm
Hole: 1.9mm (can be pressed onto a 2mm shaft)
Supplied individually. In stock -
Transistor N-MOSFET 100V 130A 370W IRFB4110GPBF
In stock
-
Push button contact round ball 12mm white 250V/1A
Single pole push button that makes contact as long as you hold it down. When you let go, the contact is broken.
In stock
-
Push button contact round ball 12mm blue 250V/1A
Single pole push button that makes contact as long as you hold it down. When you let go, the contact is broken.
In stock
-
Power cord 230V with C13 plug 1.8m black
Power cord/Power cable with earthed plug.
Connection: IEC C13 female plug
Length: 1.8 meters
Wire: 3 cores, 0.75mm2
Color: black
Maximum current: 10A
For example for computer power supplies. In stock -
Raspberry Pi HAT - Sense HAT
The Sense HAT is an expansion board for Raspberry Pi, specially made for the Astro Pi mission – it was launched to the International Space Station in December 2015.
The Sense HAT features an 8×8 RGB LED matrix, a five-button joystick and includes the following sensors:
- Gyroscope
- Accelerometer
- Magnetometer
- Temperature
- Barometric press... In stock -
Power supply 5 Volt / 5A DC Meanwell LPV-35-5
Switching 5V DC power supply from Meanwell with IP67 rating.
With protection against short circuit, overload and voltage increase.
Dimensions: 40mm x 148mm x 30mm
Input voltage: 70V-264V AC
Efficiency: 77%
IP Rating: IP67
Type: LPV-35 In stock -
Cable set JST XH 2.54mm 3-pin 30cm
Set of 2 cables with a male and female JST XH 3-pin connector. Total length of the cables incl. connectors +/- 30cm.
In stock -
Printed circuit board protection varnish CONTACT Plastic 70 200ml
Fast-drying, colourless transparent insulating and protective coating based on acrylic resins.
PLASTIK 70 is specially developed to protect printed circuit boards. It prevents electrical leakage and short circuits.
As a low-viscosity fixing and insulating lacquer, PLASTIK 70 can also be used as an additional/after
insulation of coils and transform... -
Adhesive saddle 20x20mm white
Self-adhesive saddle for mounting cables using a cable tie/tyre strip.
In stock -
Fuse holder PCB metal 5x20mm
Fuse holder for mounting on a printed circuit board. For standard fuses of 5x20mm.
You need 2 holders for 1 fuse.
In stock -
Water level sensor optical analogue
Optical water level sensor with cable of +/- 50cm.
The sensor measures whether one or more of the sensor's surfaces are in contact with a liquid.
For mounting examples, please see the article images.
Connect the sensor to 5V according to the diagram in the last picture (resistors not included, see additional articles).
The analog output can be con... -
Power connectors Deans male+female with 16AWG cable
Set of 2 cables with deans male and female connector of 10cm.
-
Clip for hot beds fixed 35mm
Clip for clamping a glass plate or other surface to the heatbed of the 3D printer.
Width: 35mm
Maximum clamp thickness: 6mm In stock -
Hotglue glue sticks 11mm/20cm black 5 pieces
5 pieces black hot glue sticks.
Diameter: 11mm
Length: 20cm
In stock -
Hotglue glue sticks 11mm/20cm transparent 5 pieces
5 pieces transparent hot glue sticks.
Diameter: 11mm
Length: 20cm
In stock -
Hotglue glue gun 11mm 80W/25W
Strong hotglue gun for 11mm hotglue sticks. The glue gun has a start-up power of 80W and then 25W.
With comfortable large trigger, operable with 4 fingers, which ensures less fatigue and easier glue dosage. -
Banana plug set 8-piece 4mm
Nickel-plated 8-piece banana plug set in 4 colours. With screw for connecting a cable (up to 4mm thick).
Set of 8 pieces: 2x red, 2x black, 2x green, 2x yellow.
Maximum voltage: 50V
Maximum current: 4A In stock -
Vacuum pick-up tool
Vacuum pick-up tool for easy picking of small ICs and SMD components weighing up to 40 grams.
Aluminum handle, length 125 mm, diameter 12 mm, curved suction nozzle and 3 separate suction cups 7-10 mm. In stock -
Brush set 3-piece
3-piece mini brush set, including for cleaning nozzles of 3D printers.
The set consists of a nylon brush, stainless steel brush and a brass brush.
Brush length: 17.5cm
Brush head width: 36mm
Bristle length: 14mm In stock -
Microswitch push button (make contact) mouse Omron D2LS-21
Omron D2LS-21 microswitch switch.
For self-repair of mouse buttons of, among others, a Logitech MX Anywhere mouse.
Dimensions: 8.6mm x 4.8mm x 3.5mm (11.2mm wide incl. pins).
See also the datasheet PDF.
Single pole switch (SPST-NO).
Adafruit Part number: 653-D2LS-21 -
Fitting for E10 screw bulb with wire
Plastic lamp socket for E10 screw bulbs with wire.
Wire length: ~11cm In stock -
Cable set JST SM 3 pins - Adafruit 1663
Male and female connector for connecting 3 pin RGB LEDs and strips.
Length: 15cm.
Can be supplied with black or coloured wires. Adafruit Part number: 1663 In stock -
Battery holder A23 / MN21 / MS21 battery
This battery holder holds one A23 / MN21 / MS21 battery.
With connection wire of approximately 15 cm.
In stock -
USB Extension Cable USB-A male-female 15cm
USB extension cable with USB-A male and female connectors.
USB Type: 2.0
Length: ~15cm
Color: black In stock -
USB Extension Cable USB-A male-female 30cm
USB extension cable with USB-A male and female connectors.
USB Type: 2.0
Length: ~30cm
Color: black In stock -
Fan axial 6010 60x60x10mm 12VDC
Axial fan 6010 for 3D printers on 12V DC.
Dimensions: 60mm x 60mm x 11mm.
Distance between holes: 50mm
Voltage: 12VDC
Cable length: ±25cm
Connector: XH2.54-2P In stock -
Fan axial 6010 60x60x10mm 24VDC
Axial fan 6010 for 3D printers on 24V DC.
Dimensions: 60mm x 60mm x 11mm.
Distance between holes: 50mm
Voltage: 24VDC
Cable length: ±25cm
Connector: XH2.54-2P In stock -
Fan axial 4020S 40x40x20mm 24VDC
Axial fan 4020S for 3D printers on 24V DC.
Dimensions: 40mm x 40mm x 20mm.
Distance between holes: 32mm
Voltage: 24VDC
Cable length: ±20cm
Connector: XH2.54-2P In stock -
Fan axial 3010S 30x30x10mm 24VDC
Axial fan 3010S for 3D printers on 24V DC.
Dimensions: 30mm x 30mm x 10mm.
Voltage: 24VDC
Connector: XH2.54-2P In stock -
Fan radial 40x40x20mm 24VDC
Radial fan 40x40x20 on 24 volts DC for 3D printers.
Dimensions: 40mm × 40mm × 20mm
Cable length: ±28cm
Connector: XH2.54-2P
Rated Voltage: 24VDC
Rated Current: 0.12Amp±10%
Rated Speed: 5800RPM±10%
Air Flow: 3.2CFM
In stock -
Temperature sensor thermistor PT100 Fork plug for Ultimaker 2
High quality PT100 Thermistor temperature sensor for, among others. use with an Ultimaker 2 3D printer.
With extra shielding and extra wire for higher accuracy.
Connection: fork cable lug
Sensor dimensions: diameter: 3mm, length: 15mm
Cable length: 150cm
Temperature range: 0 ~ 450°C
-
Temperature sensor thermistor PT100 Molex for Ultimaker 2
High quality PT100 Thermistor temperature sensor for, among others. use with an Ultimaker 2 3D printer.
With extra shielding and extra wire for higher accuracy.
Connection: molex connector
Sensor dimensions: diameter: 3mm, length: 15mm
Cable length: 150cm
Temperature range: 0 ~ 450°C
-
Temperature sensor thermocouple K-type M4 stud screw-in
High quality K-type thermocouple temperature sensor for, among others. use with a 3D printer.
Connection: fork cable lug
Sensor dimensions: M4 thread
Cable length: 100cm
Temperature range: 0 ~ 300°C
In stock -
Temperature sensor thermocouple K-type M3 stud screw-in
High quality K-type thermocouple temperature sensor for, among others. use with a 3D printer.
Connection: fork cable lug
Sensor dimensions: M3 thread
Cable length: 100cm
Temperature range: 0 ~ 300°C
In stock -
LED Board Flexible 8x8 WS2812B 5050 RGB LED with drivers (64bits)
Flexible LED board with 8x8 WS2812B RGB LEDs. The board is slightly bendable.
All LEDs can be controlled individually (on/off, color and brightness)
over 1 data line with, for example, an ESP8266/ESP32 or Arduino.
With 2 combined data in/out/power connections and 1 separate power connection.
Dimensions: 80mm x 80mm x 1.9mm (incl. LEDs)
Voltage:... In stock -
LED Board Flexible 8x32 WS2812B 5050 RGB LED with drivers (256bits)
Flexible LED board with 8x32 WS2812B RGB LEDs. The board is slightly bendable.
All LEDs can be controlled individually (on/off, color and brightness)
over 1 data line with, for example, an ESP8266/ESP32 or Arduino.
With 2 combined data in/out/power connections and 1 separate power connection.
Dimensions: 80mm x 320mm x 1.9mm (incl. LEDs)
Voltag... In stock -
Raspberry Pi DIY Protyping Hat
HAT for the Raspberry Pi 2 and 3, among others, for making your own prototypes and circuits.
With 40 pin box header, screws, spacers and nuts. In stock -
ZigBee CC2530 + CC2591 board with antenna
CC2530 ZigBee module with CC2591 amplifier and external antenna.
Compatible with ZigBee2MQTT (see left).
For instructions on how to provide the board with custom firmware for zigbee2mqtt so that you can use it with Domoticz and other home automation, see the following sites:
https://www.zigbee2mqtt.io/
You can also use an Arduino or an ESP8266 fo... -
Connector JST SM 4 pin female
Female JST SM plug with 4 pins.
For example for signal/data cables and LED strips.
- Pin spacing/grid: 2.5mm
- Supplied without contacts (see additional articles).
In stock -
Connector JST SM 2 pin female
Female JST SM plug with 2 pins.
For example for signal/data cables and LED strips.
- Pin spacing/grid: 2.5mm
- Supplied without contacts (see additional articles).
In stock -
Connector JST SM 3 pin female
Female JST SM plug with 3 pins.
For example for signal/data cables and LED strips.
- Pin spacing/grid: 2.5mm
- Supplied without contacts (see additional articles).
In stock -
Extruder drive gear wheel with grub screw for Bondtech dual drive
In stock
-
Extruder drive gear wheel without grub screw for Bondtech dual drive
In stock
-
Heatsink set for the Raspberry Pi 4 silver
4-piece heatsink set for cooling a Raspberry Pi 4.
The set consists of:
1 heatsink of 14.4mm x 14.2mm.
1 heatsink of 14.3mm x 8.9mm.
1 heatsink of 8.9mm x 8.9mm.
1 heatsink of 7mm x 7.2mm.
With thermally conductive tape for easy attachment. In stock -
Heatsink set for the Raspberry Pi 4 black
4-piece heatsink set for cooling a Raspberry Pi 4.
The set consists of:
1 heatsink of 14.4mm x 14.2mm.
1 heatsink of 14.3mm x 8.9mm.
1 heatsink of 8.9mm x 8.9mm.
1 heatsink of 7mm x 7.2mm.
With thermally conductive tape for easy attachment. In stock -
Case Raspberry Pi Zero W/WH - black
Black case for the Raspberry Pi Zero W/WH.
Supplied with self-adhesive heatsink, nuts and bolts. In stock -
Case Raspberry Pi Zero W/WH - transparent
Transparent case for the Raspberry Pi Zero W/WH.
Supplied with self-adhesive heatsink, nuts and bolts. In stock -
Laboratory connector / terminal block banana plug double black/red
Dual banana terminal blocks for mounting on an enclosure or panel.
With neat cover plate in front of and behind the panel. In stock -
Crocodile clip insulated 45mm black
Black crocodile clip with insulating sleeve.
Length: 45mm
Color: black -
Crocodile clip insulated 45mm red
Black crocodile clip with insulating sleeve.
Length: 45mm
Color: red In stock -
Crocodile clip insulated 35mm black
Black crocodile clip with insulating sleeve.
Length: 35mm
Color: black In stock -
Crocodile clip insulated 35mm red
Black crocodile clip with insulating sleeve.
Length: 35mm
Color: black In stock -
Crocodile clip insulated 28mm black
Black crocodile clip with insulating sleeve.
Length: 28mm
Color: black In stock -
Crocodile clip insulated 28mm red
Black crocodile clip with insulating sleeve.
Length: 28mm
Color: black In stock
Shipping costs Netherlands
>
